background image

Copyright

 

 

The documentation and the software included with this product are copyrighted 

2010 by Advantech Co., Ltd. All rights  are reserved. Advantech Co.,  Ltd. 

reserves the  right to make improvements  in the products described  in this 

manual at any time without notice. No part of this manual may be reproduced, 

copied, translated or transmitted in any form or by any means without the prior 

written permission of Advantech Co., Ltd. Information provided in this manual is 

intended to be accurate and reliable. How- ever, Advantech Co., Ltd. assumes 

no responsibility for its use, nor for any infringements of the rights of third 

parties, which may result from its use. 

 

 

Acknowledgements

 

Intel and Atom are trademarks of Intel Corporation. Microsoft Windows and 
MS-DOS are registered trademarks of Microsoft Corp. All other product 
names or trademarks are properties of their respective owners. 

 

 

Product Warranty (2 years)

 

 

Advantech warrants to you, the original purchaser, that each of its products will 

be free from defects in materials and workmanship for two years from the date 

of purchase. 
This  warranty does not apply to  any  products  which  have been repaired  or 

altered by persons other than repair  personnel authorized by Advantech, or 

which  have been subject  to misuse,  abuse,  accident or  improper installation. 

Advantech assumes no liability under the terms of this warranty as a 

consequence of such events. 
Because of  Advantech’s  high quality-control standards and rigorous testing, 

most of our customers never need to use  our repair service. If  an Advantech 

product is defective, it will be repaired or replaced at no charge during the 

warranty period. For out- of-warranty repairs, you will be billed according to the 

cost  of replacement materials, service time  and freight.  Please consult your 

dealer for more details. 
If you think you have a defective product, follow these steps: 

1. 

Collect all the information about the problem encountered. (For example, 

CPU speed, Advantech products used, other hardware and software used, 

etc.) Note anything abnormal and list any onscreen messages you get 

when the problem occurs. 

2. 

Call your dealer and describe the problem. Please have your manual, 

product, and any helpful information readily available. 

3. 

If your product is diagnosed as defective, obtain an RMA (return 

merchandise authorization) number from  your dealer. This allows us to 

process your return more quickly. 

4. 

Carefully pack  the defective product, a fully-completed Repair and 

Replacement Order Card and a photocopy proof of purchase date (such as 

your sales receipt) in a shippable container. A product returned  without 

proof of the purchase date is not eligible for warranty service. 

5. 

Write the RMA number visibly on the outside of the package and ship it 

prepaid to your dealer. 

 

 

 

 

 

TREK-520 User Manual 

ii 

Summary of Contents for TREK-520










































Reviews: