Advantech PPC-3211W User Manual Download Page 5

Page: 5 / 66

PPC-3151W/3211W User Manual



The equipment has been dropped or damaged. L'appareil a été abandonné et

endommagé.



The equipment shows obvious signs of breakage. L'appareil montre des signes

évidents de rupture.

15.

Do not leave the equipment in an environment with a storage temperature of

below -20 °C (-4 °F) or above 60 °C (140 °F) as this may cause damage. The

equipment should be kept in a controlled environment. Ne laissez pas cet appa

reil dans un environnement dont la température de stockage est inférieure à -20

°C (-4 °F) ou supérieure à 60 °C (140 °F), car cela pourrait causer des dom

mages. L'appareil doit être surveillé dans l'environnement.

16.

CAUTION: Batteries are at risk of exploding if incorrectly replaced. Replace only

with the same or equivalent type as recommended by the manufacturer. Discard

used batteries according to the manufacturer's instructions. ATTENTION: Il y a

danger d'explosion s'il y a remplacement incorrect de la pile. Remplacer unique

ment avec une pile du même type ou d'un type équivalent recommandé par le

constructeur.

17.

In accordance with the IEC 704-1:1982 specifications, the sound pressure level

at the operator's position does not exceed 70 dB (A). Conformément aux spéci

fications de l'IEC 704-1:1982, le niveau de pression acoustique à la position de

l'opérateur ne dépasse pas 70 dB (A).

18.

The PPC-3211W-X7XX products are intended to be supplied by a UL-certified

power supply (Adapter: FSP150-ABAN2) suitable for use at a TMA of 40 °C

(104 °F) min., with output rated 19V

, 7.89A min., ES1 (or SELV) or a UL-certi

fied power supply or DC source suitable for use at a TMA of 50 °C (122 °F) min.,

with output rated 9 ~ 32V

, 10 ~ 2.5A min., ES1 (or SELV). If you need further

assistance, contact Advantech for more information. Le produit PPC-3211W-

X7XX doit être alimenté par une alimentation certifiée UL (Adaptateur: FSP150-

ABAN2) approprié pour l'utilisation à une température de 40 °C (104 °F) au min

imum, et la sortie nominale est 19V

, 7.89A min., ES1 (ou SELV). Ou le produit

doit être alimenté par une alimentation certifiée UL ou CC pour l'utilisation à une

température de 50 °C (122 °F) au minium, et la sortie nominale est 9 ~ 32V

10 ~ 2.5A min., ES1 (ou SELV). Si vous avez besoin d'aide supplémentaire,

veuillez contacter Advantech pour plus d'informations.

19.

The PPC-3151W-X7XX products are intended to be supplied by a UL-certified

power supply (Adapter: FSP090-DIEBN2) suitable for use at a TMA of 40 °C

(104 °F) min., and output is rated 19V

, 4.74A min., ES1 (or SELV) or a UL-

certified power supply or DC source suitable for use at a TMA of 50 °C (122 °F)

min., with output rated 9 ~ 32V

, 9 ~ 2.5A min., ES1 (or SELV). If you need fur

ther assistance, contact Advantech for more information. Le produit PPC-

3151W-X7XX doit être alimenté par une alimentation certifiée UL (Adaptateur:

FSP090-DIEBN2) approprié pour l'utilisation à une température de 40 °C (104

°F) au minimum, et la sortie nominale est 19V

, 4.74 A min., ES1 (ou SELV).

Ou le produit doit être alimenté par une alimentation certifiée UL ou CC pour

l'utilisation à une température de 50 °C (122 °F) au minium, et la sortie nominale

est 9 ~ 32V

, 9 ~ 2.5A min., ES1 (ou SELV). Si vous avez besoin d'aide sup

plémentaire, veuillez contacter Advantech pour plus d'informations.

20.

DISCLAIMER: These instructions are provided in accordance with IEC 704-1

standards. Advantech disclaims all responsibility for the accuracy of any state

ments contained herein. AVERTISSEMENT: Ces instructions sont fournies con

formément aux normes IEC 704-1. Advantech décline toute responsabilité

quant à la précision de toute déclaration contenue dans le présent document.

21.

CAUTION: This product is not intended for use by children and is not suitable for

use in locations where children are likely to be present (this product is not a toy).

Summary of Contents for PPC-3211W



































































Search results

Summary of Contents for PPC-3211W

Reviews:

Advantech PPC-3211W, User Manual, Page: 5 / 66

Search results

Summary of Contents for PPC-3211W

Reviews: