manualshive.com logo in svg

Advantech PPC-3211W, User Manual, Page: 4 / 66

Share
Download
Advantech PPC-3211W User Manual Download Page 4

PPC-3151W/3211W User Manual

iv

Safety Instructions

1.

Read these safety instructions carefully. Veuillez lire attentivement ce manuel 

d'instructions de sécurité.

2.

Retain this user manual for future reference. Veuillez conserver ce manuel 

d'instructions pour référence ultérieure.

3.

Disconnect the equipment from all power outlets before cleaning. Use only a 

damp cloth for cleaning. Do not use liquid or spray detergents. Débranchez 

l'appareil de toutes les prises de courant avant le nettoyage. Nettoyez-le 

uniquement à l'aide d'un chiffon humide. Ne pas utiliser de détergents liquides 

ou pulvérisateurs.

4.

For pluggable equipment, the power outlet socket must be located near the 

equipment and easily accessible. Pour les appareils enfichables, la prise de 

courant doit être placée près de l'appareil et facilement accessible.

5.

Protect the equipment from humidity. Protégez l'appareil contre l'humidité.

6.

Place the equipment on a reliable surface during installation. Dropping or letting 

the equipment fall may cause damage. Placez l'appareil sur une surface fiable 

pendant l'installation. L'abandon ou la chute de l'appareil pourrait causer des 

dommages.

7.

The openings on the enclosure are for air convection. Protect the equipment 

from overheating. Do not cover the openings. Les ouvertures du bo?tier sont 

pour la convection d'air. Protégez l'appareil contre la surchauffe. Ne couvrez 

pas les ouvertures.

8.

Ensure that the voltage of the power source is correct before connecting the 

equipment to a power outlet. The power outlet socket should have ground con

-

nection. Assurez-vous que la tension de la source d'alimentation est correcte 

avant de connecter l'appareil à une prise de courant. La prise de courant doit 

avoir une bonne connexion mise à la terre.

9.

Position the power cord away from high-traffic areas. Do not place anything over 

the power cord. Placez le cordon d'alimentation à l'écart des zones à fort trafic. 

Ne placez rien sur le cordon d'alimentation.

10.

All cautions and warnings on the equipment should be noted. Attention à toutes 

les précautions et avertissements indiqués sur l'appareil. 

11.

If the equipment is not used for a long time, disconnect it from the power source 

to avoid damage from transient overvoltage. Si l'appareil n'est pas utilisé pen

-

dant une longue période, déconnectez-le de la source d'alimentation pour éviter 

les dommages causés par une surtension transitoire.

12.

Never pour liquid into an opening. This may cause fire or electrical shock. Ne 

versez jamais de liquide dans une ouverture. Sinon, cela pourrait provoquer un 

incendie ou un choc électrique.

13.

Never open the equipment. For safety reasons, the equipment should be 

opened only by qualified service personnel. N'ouvrez jamais l'appareil. Pour des 

raisons de sécurité, l'appareil ne doit être ouvert que par un technicien qualifié.

14.

If one of the following occurs, have the equipment checked by service person

-

nel: Si l'un des cas suivants se produit, demandez aide à un technicien qualifié:

The power cord or plug is damaged. Le cordon d'alimentation ou la fiche est 

endommagé.

Liquid has penetrated the equipment. Le liquide a pénétré dans l'appareil.

The equipment has been exposed to moisture. L'appareil a été exposé à 

l'humidité. 

The equipment is malfunctioning or does not function according to the user 

manual. L'appareil est défectueux ou ne fonctionne pas conformément aux 

instructions.

Summary of Contents for PPC-3211W



































































Reviews:

No comments