manualshive.com logo in svg

Advantech PCL-832, Manual

Share
Download
Advantech PCL-832 Manual Download Page 44

40

PCL-832  User's Manual

Function

moves the  x axis current point to a specified
point at maximum velocity and acceleration

Syntax

int MCC_ptp_x(float dx)

Parameter

dx

:

the end position of X axis in absolute
coordinate mode

the movement length of X axis in
incremental coordinate mode

Return value

0 if successful, other value if not

MCC_ptp_y   [MEX5.C]

Function

moves the y axis current point to a specified
point at maximum velocity and acceleration

Syntax

int MCC_ptp_y(float dx)

Parameter

dx

:

the end position of Y axis in absolute
coordinate mode

the movement length of Y axis in
incremental coordinate mode

Return value

0 if successful, other value if not

MCC_ptp_z   [MEX5.C]

Function

moves the z axis current point to a specified
point at maximum velocity and acceleration

Syntax

int MCC_ptp_z(float dx)

Parameter

dx

:

the end position of Z axis in absolute
coordinate mode

the movement length of Z axis in
incremental coordinate mode

Return value

0 if successful, other value if not

Summary of Contents for PCL-832
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands