Advantech IEEE 802.11a/n Wireless Access Point/ Client Bridge User Manual Download Page 49

Page: 49 / 83

EKI-6331AN_User Manual

Page 40

Configure SNMPv3 User Profile

For SNMP protocol version 3, you can click “Configure SNMPv3 User Profile” in blue to set the

details of SNMPv3 user. Check “Enable SNMPv3 Admin/User” in advance and make further

configuration.

Figure 33 Configure SNMPv3 User Profile

User Name

Specify a user name for the SNMPv3 administrator or user. Only the SNMP commands carrying

this user name are allowed to access EKI-6331AN.

Password

Specify a password for the SNMPv3 administrator or user. Only the SNMP commands carrying

this password are allowed to access EKI-6331AN.

Confirm Password

Input that password again to make sure it is your desired one.

Access Type

Select “Read Only” or “Read and Write” accordingly.

Authentication Protocol

Select an authentication algorithm. SHA authentication is stronger than MD5 but is slower.

Privacy Protocol

Specify the encryption method for SNMP communication. None and DES are available.

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge




















































































Search results

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Reviews:

Related manuals for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Brands by name

Popular brands

Advantech IEEE 802.11a/n Wireless Access Point/ Client Bridge, User Manual

Search results

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Reviews:

Related manuals for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Brands by name

Popular brands