Advantech IEEE 802.11a/n Wireless Access Point/ Client Bridge User Manual Download Page 47

Page: 47 / 83

EKI-6331AN_User Manual

Page 38

Chapter 5 Management

Remote Management

EKI-6331AN provides a variety of remotes managements including Telnet, SNMP, FTP, SSH, HTTPS

and exclusive WISE tool, making configuration more convenient and secure.

With Normal selected, Telnet, SNMP and FTP are activated as default remote management options.

To use secure management tools such as SSH, HTTPS and WISE, please select “Secure”. You may

also choose “Customized” to enable any methods as desired.

Figure 31 Remote Management

SNMP Management

EKI-6331AN supports SNMP for convenient remote management. Open “Remote Settings” in

“Management” shown below. Set the SNMP parameters and obtain MIB file before remote

management.

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge




















































































Search results

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Reviews:

Related manuals for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Brands by name

Popular brands

Advantech IEEE 802.11a/n Wireless Access Point/ Client Bridge, User Manual

Search results

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Reviews:

Related manuals for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Brands by name

Popular brands