Advantech IEEE 802.11a/n Wireless Access Point/ Client Bridge User Manual Download Page 24 | Manualshive

Page: 24 / 83

background image

EKI-6331AN_User Manual

Page 15

Enter the username (Default: admin) and password (Default: password) respectively and click

“Login” to login the main page of EKI-6331AN. As you can see, this management interface

provides 5 main options in the black bar above, which are Status, System, Wireless,

Management and Tools.

Figure 10 Main Page

The username and password are case-sensitive, and the password should be no

more than 19 characters!

Note:

«
...
22
23
24
25
26
...
»

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge




















































































Reviews:

No comments

Related manuals for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Brand: Ocens Pages: 2

Brand: X-Micro Pages: 76

Brand: Hawking Pages: 2

EnOcean TALK MODUL G2

Brand: Waldmann Pages: 68

Brand: Ruby Tech Pages: 17

Brand: Edimax Pages: 2

Brand: ALCON Pages: 47

EVlinking Wi-Fi

Brand: Evco Pages: 18

Barricade SMCWBR14S-N3

Brand: SMC Networks Pages: 106

Brand: Advantech Pages: 46

RTA 1046VW ADSL1

Brand: Dynalink Pages: 5

Wireless LAN Client PCMCIA WLC030

Brand: Dynalink Pages: 10

Brand: EnGenius Pages: 2

Brand: Cambium Networks Pages: 15

Brand: ConnectGear Pages: 11

Brand: ConnectGear Pages: 36

Brand: ConnectGear Pages: 40

Brand: ConnectGear Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands