Advantech IEEE 802.11a/n Wireless Access Point/ Client Bridge User Manual Download Page 48

Page: 48 / 83

EKI-6331AN_User Manual

Page 39

Figure 32 SNMP Configuration

Protocol Version

Select the SNMP version, and keep it identical on EKI-6331AN and the SNMP manager.

EKI-63331AN supports SNMP v2/v3.

Server Port

Change the server port for a service if needed; however you have to use the same port to use that

service for remote management.

Get Community

Specify the password for the incoming Get and GetNext requests from the management station.

By default, it is set to public and allows all requests.

Set Community

Specify the password for the incoming Set requests from the management station. By default, it is

set to private.

Trap Destination

Specify the IP address of the station to send the SNMP traps to.

Trap Community

Specify the password sent with each trap to the manager. By default, it is set to public and allows

all requests.

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge




















































































Search results

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Reviews:

Related manuals for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Brands by name

Popular brands

Advantech IEEE 802.11a/n Wireless Access Point/ Client Bridge, User Manual

Search results

Summary of Contents for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Reviews:

Related manuals for IEEE 802.11a/n Wireless Access Point/ Client Bridge

Brands by name

Popular brands