Advantech iDAQ-817 User Manual Download

Page: 4 / 36

iDAQ-817_821 User Manual

Warnings, Cautions, and Notes

Document Feedback

To assist us with improving this manual, we welcome all comments and constructive

criticism. Please send all such feedback in writing to [email protected].

Packing List

Before system installation, check that the items listed below are included and in good

condition. If any item does not accord with the list, contact your dealer immediately.

iDAQ-817



iDAQ-817 x 1



10-pin terminal block x 2



Startup Manual x 1

iDAQ-821



iDAQ-821 x 1



10-pin terminal block x 1



Startup Manual x 1

Warning!

Warnings indicate conditions that if not observed can cause personal

injury!

Caution!

Cautions are included to help prevent hardware damage and data

losses. For example,
“Batteries are at risk of exploding if incorrectly installed. Do not attempt

to recharge, force open, or heat the battery. Replace the battery only

with the same or equivalent type as recommended by the manufacturer.

Discard used batteries according to the manufacturer's instructions.”

Note!

Notes provide additional optional information.

Summary of Contents for iDAQ-817





































Search results

Summary of Contents for iDAQ-817

Reviews:

Related manuals for iDAQ-817

Brands by name

Popular brands

Advantech iDAQ-817, User Manual

Search results

Summary of Contents for iDAQ-817

Reviews:

Related manuals for iDAQ-817

Brands by name

Popular brands