background image

iDAQ-817_821 User Manual

ii

Copyright

The documentation and the software included with this product are copyrighted 2021

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right

to make improvements in the products described in this manual at any time without

notice. No part of this manual may be reproduced, copied, translated, or transmitted

in any form or by any means without the prior written permission of Advantech Co.,

Ltd. The information provided in this manual is intended to be accurate and reliable.

However, Advantech  Co.,  Ltd.  assumes  no  responsibility  for  its  use,  nor  for  any

infringements of the rights of third parties that may result from its use.

Acknowledgments

Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.

Product Warranty (2 years)

Advantech warrants the original purchaser that each of its products will be free from

defects in materials and workmanship for two years from the date of purchase. 
This warranty does not apply to any products that have been repaired or altered by

persons other than repair personnel authorized by Advantech, or products that have

been  subject  to  misuse,  abuse,  accident,  or  improper  installation.  Advantech

assumes  no  liability  under  the  terms  of  this  warranty  as  a  consequence  of  such

events.
Because  of Advantech’s  high  quality-control  standards  and  rigorous  testing,  most

customers never need to use our repair service. If an Advantech product is defective,

it will be repaired or replaced free of charge during the warranty period. For out-of-

warranty repairs, customers will be billed according to the cost of replacement mate

-

rials, service time, and freight. Please consult your dealer for more details.
If you believe your product is defective, follow the steps outlined below.

1.

Collect all the information about the problem encountered. (For example, CPU 

speed, Advantech products used, other hardware and software used, etc.) Note 

anything abnormal and list any onscreen messages displayed when the prob

-

lem occurs.

2.

Call your dealer and describe the problem. Please have your manual, product, 

and any helpful information readily available.

3.

If your product is diagnosed as defective, obtain a return merchandise authori

-

zation (RMA) number from your dealer. This allows us to process your return 

more quickly.

4.

Carefully pack the defective product, a completed Repair and Replacement 

Order Card, and a proof of purchase date (such as a photocopy of your sales 

receipt) into a shippable container. Products returned without a proof of pur

-

chase date are not eligible for warranty service.

5.

Write the RMA number clearly on the outside of the package and ship the pack

-

age prepaid to your dealer.

Part No. 2001081700

Edition 1

Printed in China

November 2021

Summary of Contents for iDAQ-817





































Reviews: