3
FWA-1320 User Manual
C
h
ap
te
r 1
G
et
tin
g
S
ta
rte
d
14.
If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
1.1.2
Safety Precautions - Static Electricity
Follow instructions below to protect yourself from harm and the products from dam-
age:
1.
Be sure you are at an ESD workstation, or grounded with an ESD strap before
opening the top cover or installing/removing any unit accessible from the out-
side. Doing so will discharge any static electricity that might have built up in your
body.
2.
Don’t touch any components inside the system while the system is on.
3.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.
4.
When unpacking a static-sensitive component from its shipping carton, do not
remove the component's antistatic packing material until you are ready to install
the component in the unit.
5.
When transporting any electrical component, first place it in an antistatic con-
tainer or packaging.
1.2
Unpacking
Please check the delivery for completeness as you open the carton carefully. If
any of the items listed in Table 1 is missing or damaged, please contact your
Advantech representative.
When opening the box, you will find the FWA-1320 embedded in protective foam and
the accessory box embedded to the foam. Remove the accessory box first and then
pull out the unit including the protective foam using both hands. Now, remove the
foam and the plastic sleeve on the unit.
After unpacking the unit, please check for any visible damage of the unit and contact
your Advantech representative in case of any issue.
Summary of Contents for FWA-1320
