Advantech EKI-6310GN User Manual Download Page 39

Page: 39 / 107

EKI-6310GN User Manual

Chapter 4

etwork

Settings



IPv6 PPPoE
Use Point-to-Point Protocol over Ethernet (PPPoE) network protocol to dial-in
ISP network.

Figure 4.14 IPv6 PPPoE Settings

Login

: Enter your PPPoE user name.

Password

: Enter your PPPoE password and then retype the password in the

next box.

IPV6 Primary DNS Server

: Enter the WAN primary DNS Server address used

here.

IPV6 Secondary DNS Server: Enter the WAN secondary DNS Server address
used here.

Ebable DHCP-PD

: Enable DHCP-PD Support.

SLD ID

: Site-Level Aggregation Identifier

SLA Length

: Length of site-level aggregation identifier (SLA).

LAN IPv6 IP Address

: These are the settings of the LAN (Local Area Network)

IPv6 interface for the router. The router's LAN IPv6 Address configuration is
based on the IPv6 Address and Subnet assigned by your ISP. (A subnet with
prefix /64 is supported in LAN.)

IPV6 AutoConfiguration

: EKI-6310GN autonomously configures its own Link-

Local address. Router solicitation is sent by booting nodes to request RAs for
configuring the interfaces.

Summary of Contents for EKI-6310GN












































































































Search results

Summary of Contents for EKI-6310GN

Reviews:

Related manuals for EKI-6310GN

Brands by name

Popular brands

Advantech EKI-6310GN, User Manual

Search results

Summary of Contents for EKI-6310GN

Reviews:

Related manuals for EKI-6310GN

Brands by name

Popular brands