Advantech Wireless AWMA-Kx500-BTE Series Installation And Operating Manual Download Page 30 | Manualshive

Page: 30 / 51

background image

AWMA-Kx500-BTE

6.3.3 M

ECHANICAL

, RF

AND

E

LECTRICAL

I

NSTALLATION

6.3.3.1 Single Unit Installation

1. Bolt the SSPA unit at the antenna hub by using the six mounting holes provided by the

enclosure, see

2. Position the interconnecting waveguide system flange so that it aligns precisely with the

waveguide flange of the SSPA RF output port.

3. Install the supplied waterproof gasket (supplied in the packing list

)

on to the interconnecting

waveguide flange.

CAUTION:

If the waveguide is intended to be pressurized, do not exceed 2-3 psi pressure,

in order to protect the inside pressure window installed by Advantech Wireless.

4. After alignment verification, loosely attach the interconnecting waveguide on to the RF output

port using the hardware provided in the shipping kit.

5. Carefully tighten all bolts (in opposite pairs rather than sequentially around the perimeter of the

flange) so that the connection is firm.

CAUTION:

Do not over-tighten the waveguide flange screws. Over-tightening the bolts

may cause the stripping of the threads or distort the mating flange. Recommended torque is
15 in-lbs for #6-32 bolts.

6. Ground the SSPA unit by attaching a #6 gauge copper wire to the ground terminal provided by

the unit enclosure to a properly grounded structure.

7. If it is desired to use the Relay interface, then attach the interconnecting cable fabricated per

Section 6.3.1

to the Relay connector of the SSPA unit. Connect the free end of the

interconnecting cable to the operator’s monitor and control system.

NOTE:

Whether this interface is being used or not, it is necessary to connect pin G of the
Relay connector to pin H (common) in order to enable (un-mute) the transmission
path. If pin G of this interface is not connected to pin H, the transmission path of the
unit will remain muted.

8. If it is desired to use the RS-485 interface, then connect the interconnecting cable fabricated per

Section 6.3.1

to the RS-485 port of the SSPA unit.

9. If it is desired to use the RS-232 terminal mode, then:

29

«
...
28
29
30
31
32
...
»

Summary of Contents for AWMA-Kx500-BTE Series




















































Reviews:

No comments

Related manuals for AWMA-Kx500-BTE Series

Brand: Cable Electronics Pages: 2

Brand: NAD Pages: 18

Brand: NAD Pages: 2

PowerLight PL-3.4

Brand: QSC Pages: 2

Brand: QSC Pages: 2

Brand: dB Technologies Pages: 133

Brand: VINCENT Pages: 60

Brand: B&K Pages: 16

Reference 750 SE

Brand: Audio Research Pages: 18

Brand: NAD Pages: 12

Brand: Tekbox Pages: 10

Brand: Acoustic Pages: 8

Brand: E&I Pages: 12

Brand: PJB Pages: 7

Brand: NAIM Pages: 32

Brand: MIXHITS AUDIO Pages: 14

Brand: Godin Pages: 10

1000 Roc-Pro 22-6878

Brand: Fender Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands