manualshive.com logo in svg

Advantech Wireless AWMA-Kx500-BTE Series, Installation And Operating Manual

Share
Download
Advantech Wireless AWMA-Kx500-BTE Series Installation And Operating Manual Download Page 11

 

 

 

 

AWMA-Kx500-BTE

3. GENERAL INFORMATION 

 

 

This manual contains information that describes installation, operation and maintenance procedures 
for the 500 W Kx-Band hub-mount (outdoor) Solid State Power Amplifier (SSPA), model AWMA-
Kx500-BTE. Because specialized training is required for some phases of installation and operation, 
certain parts of this manual are directed only to trained personnel. Warnings appear at the 
appropriate points to caution all users of potential RF and high-voltage hazards. 
 
For a safe and versatile operation, please read the information carefully BEFORE using the 
equipment. 
 
 
 

Advantech Wireless has prepared this manual for use by customers as a guide for the proper 
installation, operation and maintenance of Advantech Wireless equipment and computer programs. 
The drawings, specifications, and information contained herein are property of Advantech 
Wireless. Any unauthorized use or disclosure of these drawings, specifications and information is 
prohibited; they shall not be reproduced, copied or used in whole or in part as the basis for 
manufacturing or sale of the equipment or software programs without the prior written consent of 
Advantech Wireless. 

 
 
 

 

10

 

Summary of Contents for AWMA-Kx500-BTE Series




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands