background image

F.

 

HOW TO: SET AND ADJUST UPPER AND LOWER LIMITS 

 

1.

 

ALWAYS SET THE LOWER LIMIT FIRST 
 

2.

 

USE THE DOWN ARROW ON THE REMOTE TO MOVE THE BOTTOM BAR DOWN. IF THE BOTTOM 
BAR DOES NOT STOP BEFORE 1’ FROM THE BOTTOM, PRESS THE STOP BUTTON TO STOP IT 1’ 
FROM THE BOTTOM.  

 

3.

 

THE WHITE RECTANGULAR BLOCK ON THE VISIBLE END OF THE MOTOR HAS TWO HOLES 
CONTAINING THE LIMIT ADJUSTMENT SWITCHES. THE LIMIT ADJUSTMENT SWITCH THAT 
CONTROLS THE LOWER LIMIT IS ALWAYS IN THE TOP HOLE REGARDLESS OF WHICH SIDE (left or 
right) THE MOTOR IS MOUNTED. ABOVE THE TOP HOLE, THERE IS AN ARROW ABOVE THE PLUS 
(+) SIGN AND THERE IS AN ARROW ABOVE THE MINUS (-) SIGN. TURNING THE LIMIT 
ADJUSTMENT TOOL IN THE DIRECTION OF THE PLUS (+) ARROW or the counter-clockwise 
DIRECTION INCREASES THAT LIMIT AND TURNING THE LIMIT ADJUSTMENT TOOL IN THE 
DIRECTION OF THE MINUS (-) ARROW or the clockwise DIRECTION REDUCES THAT LIMIT. 

 

4.

 

NOW ADJUST THE LOWER LIMIT: 

 

1. IF THE SCREEN STOPPED BEFORE IT GOT TO 
WITHIN 1' OF THE BOTTOM 

2. IF YOU HAD TO  STOP THE SCREEN BEFORE 
IT GOT TO WITHIN 1' OF THE BOTTOM 

1-A. YOU HAVE FOUND THE FACTORY-SET 
TEMPORARY LOWER LIMIT. HOWEVER, THE 
FACTORY-SET TEMPORARY LOWER LIMIT IS 
TOO SHORT. SO, YOU NEED TO INCREASE THE 
LOWER LIMIT POSITION 

2-A. THE FACTORY-SET TEMPORARY LOWER 
LIMIT IS SET TOO LONG. THEREFORE, YOU 
NEED TO REDUCE THE LOWER LIMIT POSITION. 

1-B. PLACE THE LIMIT ADJUSTMENT TOOL 
INTO THE TOP HOLE ON THE END OF THE 
MOTOR. TURN THAT LIMIT ADJUSTMENT 
SWITCH IN THE DIRECTION OF THE PLUS (+) 
ARROW or the counter-clockwise DIRECTION. 
THE BOTTOM BAR WILL JOG DOWN WITH 
EACH TURN. CONTINUE TO TURN UNTIL THE 
BOTTOM BAR REACHES THE DESIRED LOWER 
POSITION. AT THAT POINT YOUR LOWER LIMIT 
IS SET. 

2-B. PLACE THE LIMIT ADJUSTMENT TOOL 
INTO THE TOP HOLE ON THE END OF THE 
MOTOR. TURN THAT LIMIT ADJUSTMENT 
SWITCH IN THE DIRECTION OF THE MINUS (-) 
ARROW or the clockwise DIRECTION FOR 25 
COMPLETE TURNS. 
 
Note: 7 complete turns of the Limit 
Adjustment Tool results in one complete 
rotation of the screen tube. 

 

2-C. USING THE REMOTE, RAISE THE BOTTOM 
BAR 2 FEET AND THEN LOWER IT. IF IT DOES 
NOT STOP BEFORE IT REACHES 1' FROM THE 
BOTTOM, STOP IT 1' FROM THE BOTTOM.  

 

2-D. REPEAT STEPS 2-B AND 2-C UNTIL THE 
BOTTOM BAR STOPS BY ITSELF. WHEN THE 
BOTTOM BAR STOPS BY ITSELF YOU HAVE 
FOUND THE TEMPORARY LOWER LIMIT.  

 

2-E. PERFORM INSTRUCTION 1. (1-A AND 1-B) 
ON THE LEFT COLUMN OF THIS TABLE OF 
INSTRUCTIONS TO FINE TUNE THE LOWER 
LIMIT. 

Summary of Contents for Mystic Series














Reviews: