Advanced Radiant Systems VA Range Installation, Operation And Service Instructions Download Page 22

Page: 22 / 44

Page 18

Modulating Unitary Range

VA-LT206_11292016al

INSTALLATION

Note:

Reflectors should overlap adjacent reflectors 4" to 6". Be sure not to tile reflector sections; that is, reflector

sections must be either above both adjacent reflector sections, or below both adjacent reflector sections. (Refer

to Figure 16).

VENT

TERMINATION

END

REFLECTOR

SUPPORT

LOOSE

SCREWS

TIGHT

SCREWS

LOOSE

SCREWS

TIGHT

SCREWS

FASTEN ENDCAP

WITH SCREWS

REFLECTOR OVERLAP

APPROX. 6"

HEATER END

NOTE:

DO NOT ALLOW

TIGHTENED SCREWS TO

PENETRATE REFLECTORS

REFLECTOR OVERLAP ILLUSTRATION

Scale: NTS

REFLECTOR

SUPPORT

LOOSE

SCREWS

TIGHT

SCREWS

LOOSE

SCREWS

TIGHT

SCREWS

FASTEN ENDCAP

WITH SCREWS

REFLECTOR OVERLAP

APPROX. 6"

HEATER END

DO NOT ALLOW

TIGHTENED SCREWS TO

PENETRATE REFLECTORS

Figure 16: Reflector Support Bracket Installation

Summary of Contents for VA Range













































Search results

Summary of Contents for VA Range

Reviews:

Related manuals for VA Range

Brands by name

Popular brands

Advanced Radiant Systems VA Range, Installation, Operation And Service Instructions

Search results

Summary of Contents for VA Range

Reviews:

Related manuals for VA Range

Brands by name

Popular brands