manualshive.com logo in svg

Advanced Instruments Osmo1, Service Manual, Page: 16 / 55

Share
Download
Advanced Instruments Osmo1 Service Manual Download Page 16

16

Osmo1

™

 Single-Sample Micro-Osmometer Service Guide

Chapter 2 

Setup

This chapter describes how to set up the Osmo1 
instrument in the laboratory.

2.1  Location requirements

The location of the Osmo1 must meet the following 
space and electrical requirements.

Osmo1 dimensions

• 

Not including Micro-Sample Test Kit: 
15" D x 14" W x 10" H 
(38 cm D x 36 cm W x 25 cm H)

• 

Including Micro-Sample Test Kit: 
15" D x 14" W x 15" H 
(38 cm D x 36 cm W x 38 cm H)

Recommended clearance

Allow 6 inches (15 cm) of clear space on each side of the 
instrument.

Do not block the exhaust fan airflow on the back panel 
or underneath the instrument.

Electrical requirements

Your instrument must be located within five 
feet of a properly grounded, three-prong 
electrical outlet capable of continuously 
supplying 0.5 amperes at 100–240 VAC 
(50–60 Hz).

If the instrument is not grounded properly, its 
operation may be impaired and a safety hazard 
may exist. Verify that the outlet is appropriate 
before operating the instrument.

Do not disable the grounding plug.

2.2  Loading the printer paper 

To prepare the instrument for use, install one roll of 
paper as directed below.

1. 

Lift to open the printer door located on the top right 
of the instrument.

2. 

Unroll 4-6” (15-20 cm) of thermal paper from the roll.

3. 

Hold the roll so that the paper feeds upwards from 
the bottom of the roll towards the front of the 
instrument, and place the roll into the printer 
(Figure 5).

Feed paper 

from bottom

Figure 5: Printer paper roll orientation, door open

Summary of Contents for Osmo1
























































Reviews:

No comments