Advance acoustic Adfinity 17ST Service Manual Download Page 5

Page: 5 / 92

SERVICE MANUAL

ENGLISH

Adfinity™ 17ST / 20ST / X20R / 20D / X20D / X20C / X24D

9096982000

GENERAL INFORMATION

CONVENTIONS

Forward, backward, front, rear, left or right are intended with reference to the operator’s position, that is to say in driving position

with the hands on the handlebar.

MACHINE LIFTING

WARNING!

Do not work under the lifted machine without supporting it with safety stands.

MACHINE TRANSPORTATION

WARNING!

Before transporting the machine, make sure that:

–

All covers are closed.

–

The ignition key is removed.

–

The machine is securely fastened to the means of transport.

OTHER REFERENCE MANUALS

The following manuals are available at Advance Literature Service Department:

–

Adfinity™ 17ST, 20ST, X20R: User Manual - Form Number 9096912000

–

Adfinity™ 17ST, 20ST, X20R: Spare Parts List - Form Number 9096913000

–

Adfinity™ 20D, X20D, X20C, X24D: User Manual - Form Number 9096910000

–

Adfinity™ 20D, X20D, X20C, X24D: Spare Parts List - Form Number 9096911000

–

Installation instructions counter hour kit - Form Number 9096952000

–

Installation instructions for extra pressure kit - Form Number 909 6759 000

–

Installation instructions for splash guard kit - Form Number 909 6745 000

–

Installation instructions for battery charger kit - Form Number 909 6746 000

–

Installation instructions for EcoFlex™ system kit Delta 6 - Form Number 9096936000

–

Installation instructions for EcoFlex™ system kit Delta 7- Form Number 909 6747 000

Summary of Contents for Adfinity 17ST





























































































Search results

Summary of Contents for Adfinity 17ST

Reviews:

Related manuals for Adfinity 17ST

Brands by name

Popular brands

Advance acoustic Adfinity 17ST, Service Manual

Search results

Summary of Contents for Adfinity 17ST

Reviews:

Related manuals for Adfinity 17ST

Brands by name

Popular brands