Advance acoustic Adfinity 17ST Service Manual Download Page 14

Page: 14 / 92

ENGLISH

SERVICE MANUAL

9096982000

Adfinity™ 17ST / 20ST / X20R / 20D / X20D / X20C / X24D

GENERAL INFORMATION

MAINTENANCE

The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance

WARNING!

Read carefully the instructions in the Safety chapter before performing any maintenance procedure.

The following tables provides the scheduled maintenance. The intervals shown may vary according to particular working conditions,

which are to be defined by the person in charge of the maintenance.
For instructions on maintenance procedures, see the following paragraphs.

SCHEDULED MAINTENANCE TABLE

Procedure

Daily, after

machine use

Weekly

Every six

months

Yearly

Battery charging

Squeegee cleaning

Brush/pad cleaning

Tank and vacuum grid with float cleaning, and cover gasket check

Squeegee blade check and replacement

EcoFlex™ system cleaning and draining

Solution/clean water filter cleaning

Battery (WET) fluid level check

Vacuum system motor filter cleaning

Screw and nut tightening check

(1)

Brush/pad-holder motor carbon brush check or replacement

Vacuum system motor carbon brush check or replacement

Drive system motor carbon brush check or replacement

(For Adfinity™ X20R, 20D, X20D, X20C, X24D)

(1): And after the first 8 working hours.

Summary of Contents for Adfinity 17ST





























































































Search results

Summary of Contents for Adfinity 17ST

Reviews:

Related manuals for Adfinity 17ST

Brands by name

Popular brands

Advance acoustic Adfinity 17ST, Service Manual

Search results

Summary of Contents for Adfinity 17ST

Reviews:

Related manuals for Adfinity 17ST

Brands by name

Popular brands