ADS idatastart HC2351AC Product Manual Download Page 12

Page: 12 / 12

U.S. Patent No. 8,856,780

MODULE RESET PROCEDURE - 1 OF 1

The following procedure resets the module

programming to the vehicle. It does not reset

any settings confi gured online.

Disconnect all connectors from module except

the M1 BLACK 8-pin connector and the M4

BLACK 20-pin connector.

Disconnect the M1 BLACK 8-pin connector

and the M4 BLACK 20-pin connector.

PRESS AND HOLD the module’s programming

button while connecting the M1 BLACK

8-pin connector and the M4 BLACK 20-pin

connector.

Wait, LED 1 will ﬂash RED. RELEASE

programming button.

LED 1 will turn RED for 2 seconds.

Module RESET completed.

Reconnect all connectors.

Repeat programming procedure.

Failure to follow procedure may result with a

DTC or a CHECK ENGINE error message.

www.idatalink.com

HC2351AC

PAGE 12 OF 12

• 20161024

Summary of Contents for idatastart HC2351AC













Search results

Summary of Contents for idatastart HC2351AC

Reviews:

Related manuals for idatastart HC2351AC

Brands by name

Popular brands

ADS idatastart HC2351AC, Product Manual

Search results

Summary of Contents for idatastart HC2351AC

Reviews:

Related manuals for idatastart HC2351AC

Brands by name

Popular brands