background image

U.S. Patent No. 8,856,780

REMOTE STARTER ERROR CODES

 - 1 OF 1

REMOTE STARTER ERROR CODES:

NOTES

[X] NUMBER OF  PARKING LIGHT  FLASHES

DIA

GNOSTIC

I WARNING: The following applies only when the parking 

lights are connected and supported by the system.

01

Engine running. 

02

Key in ignition at ON position.

II After a remote starter failure, the parking lights will fl ash 

three [3x] times, then will fl ash [X] number times to 

indicate an error code. See table.

03

Door is open.

04

Trunk is open.

05

Foot brake is ON. 

06

Hood is open.

07

The reservation is OFF. (Manual transmission only)

08

Tach failure.

09

The vehicle is moving (VSS).

10

System is in Valet Mode. 

11

CAN communication failure

12

RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.

13

Bypass problem.

REMOTE STARTER SHUTDOWN ERROR CODES:

NOTES

[Y] NUMBER OF  PARKING LIGHT  FLASHES

DIA

GNOSTIC

I WARNING: The following applies only when the parking 

lights are connected and supported by the system.

01

Engine tach signal is lost.

02

Emergency brake is lost.

II

If the engine shuts down after a remote starter sequence: 

Press and hold the Trunk button and the Start button at the 

same time for 2.5 seconds when using a 1-WAY remote. 

OR 

Press once [1x] on button “4” when using a 2-WAY remote. 

The parking lights will fl ash four [4x] times, then will fl ash 

[Y] number times to indicate an error code. See table.

03

Foot brake is ON. 

04

Hood is open.

05

Engine RPM limiter is ON.

06

Glow plug timeout error.

07

Vehicle is moving (VSS).

08

N/A

09

N/A

10

Door is open.

11

CAN communication failure during RS sequence.

12

RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.

13

Takeover is not allowed.

14

Shutdown error, board overheat protection.

www.idatalink.com

Automotive Data Solutions Inc. © 2016

HC2351AC

PAGE 11 OF 12

• 20161024

Summary of Contents for idatastart HC2351AC













Reviews: