background image

4.  The user should make sure that the installation is carried out by qualified authorised persons and that these persons have first carefully
  read the following instructions.

5.  The operating safety of the Admiral ATV-NAV is only guaranteed if the installation and operation instructions are correctly followed.

6.  In the event of defective operation or fault, contact Waterco or its nearest authorised service agent.

7.  To reduce the risk of injury, do not permit children to use this product.

8.  Incorrectly installed equipment may fail, causing severe injury or property damage.

9.  Chemical spills and fumes can weaken the Admiral ATV-NAV. Corrosion can cause the cleaner and other equipment to fail, resulting in severe
  injury or property damage. Do not store pool chemicals near your equipment.

10.

 

Do not play with the Admiral ATV-NAV or power cable as potential entrapment of hair or body parts may result. The power cord can

  trip or entangle swimmers which could result in drowning.

11.

 

Your Admiral ATV-NAV should not be used while people are swimming in the pool.

GENERAL INSTRUCTIONS

 

Maximum Recommended Pool Size: 9m x 12m x 2.4m depth. 

  Minimum Recommended Pool Size: 3m x 3m.

 

If ambient air temperature exceeds 46ºC (115ºF), protect the Admiral ATV-NAV’s power supply from direct sunlight. However, ensure power

  supply has adequate ventilation.

 

Do not connect the Admiral ATV-NAV’s power supply (transformer) to AC power until installation has been completed.

 

Do not use if unit is damaged in any way.

 

Make sure the Admiral ATV-NAV is unplugged from its power supply before opening the unit or performing any other maintenance. 

 

To avoid damage to the power supply & power cord, never carry the power supply by the power cord or pull on the

  power cord to disconnect from an outlet. Disconnect by pulling the plug, itself, from the outlet.

 

Do not pull power cord around sharp corners or edges.

 

Do not operate with a damaged power cord or power supply.

 

Before installing the Admiral ATV-NAV, understand the cleaner’s coverage. The cleaner was not designed to automatically clean steps or to work

  under solar covers. It was also not designed to do an initial clean up for a new pool installation.

 

The power supply must be at least 4m (12ft) from the pool’s edge at all times!.

 

It is recommended that you clean your Admiral ATV-NAV filter bag and check the impeller to make sure it is free and clear of debris

  after every use.

 

Disconnect the power supply supply from the outlet when not in use.

 

DO NOT switch the Admiral ATV-NAV to “ON” if it is not immersed in water. Operating the cleaner out of water may cause severe damage & will

  result in loss of warranty. Always remember to turn the power supply “OFF” and unplug it from the power outlet before removing the
  cleaner from the pool.

3

Summary of Contents for ATV-NAV





















Reviews: