41310 SERIES GAZEBO.0923-15.EFS 2017
2
1.
Do not attempt to assemble the screenhouse under windy
conditions.
2.
In the event strong winds or storms are forecasted,
disassemble and store in a safe place. Minimum Precaution
requires removal of the roof.
3.
While this screenhouse meets CPAI Code 84 requirements
for flame retardancy, it is NOT fire proof. Keep open flames
and flammable materials outside and at a safe distance from
your screenhouse.
1.
Prior to assembly
A.
To safely and easily assemble the screenhouse a minimum
of two people are needed. You will need a medium-sized
square-slothead screwdriver, nut driver, adjustable wrench and
a stepladder.
B.
You should erect your screen room on as level a base as
possible.
C.
Remove the vinyl roof, roof tubes, vinyl hinges and the
door hardware and inventory parts as listed on page 9 for your
model.
2.
To assemble the wall
A.
Form a rough rectangle or square with screening on the
outside like a diagram, making certain center bars are inside
the room.
B.
Position opening where you desire the door.
C.
Line up the edge of the two end frames.
D.
While holding one end of the vinyl hinge vertically above
the two frames, slowly insert it simultaneously into both
frames until completely inserted.
3.
Door installation
To install as pre-assembled in
factory, take the (85-056) plastic
tracks from the box and slide on the extrusion at the top side
and bottom side of the door opening, the open side of the top
track facing down with two holes and up on the bottom, no
holes.
A.
Slide door into position. Make sure the wheels are at the
bottom and the screen towards the outside of the room, then
drill two holes for the handles (85-050) at the height you
desire.
B.
Install weather strip (85-058) on both 74’’ high parts of the
door frame, facing in.
4.
Frame fixture
Take bracket 94-233 (94-220 or 94-219) and screw on two
frames. The screws that fall at the door need to be turned
around the other way from inside out, as well as the screw at
the end where the door is in a closed position (3 screws).
5.
To assemble roof
A.
Take the four special brackets and slide in upper section of
the middle panel frame located on each side.
B.
Take rope provided and insert in the hole of one of the
brackets and tie a knot.
C.
Repeat on opposite side to keep form temporarily in its
shape until all the roof is in place.
D.
Repeat step B & C.
E.
One person should be on the stool or stepladder in the
center of the screen room holding one of the hubs angled
downward and even with the top of the screening panels.
F.
The second person starts to take the tubes in order as per
the appropriate diagram, place them on the hub and tube tip.
G.
Placing tube tip through tube tip bracket as illustration
shows.
8
”
10
10
41010
1
/
2
8
8
11
9
9
7
12
7
9
7
9
9
9
3
2
2
11
11
11
14
6
9
9
16
7
7
7
41612
2
2
2
14
9
9
7
14
6
6
12
12
12
14
14
1
7
9
9
4
9
5
7
7
9
9
9
9
9
9
8 8
41112
41310
41512
1
/
2
14
6
6
6
12
12
12
14
14
15
41514
5
13
10
10
2
2
2
2
10
10
1
41110
2
2
10
2
9
9
9
9
9
6
6
10
12
13
2
40808
1
43 5/8”
2
50 1/4"
3
21 3/4"
4
51 1/2"
5
73 1/2"
6
53 1/2"
7
57 3/4"
8
67”
9
60 1/4"
10
66 1/2"
11
51”
12
69”
13
71”
14
82”
15
88 3/8”
16
96”
