Adjust-a-Sink K100 Series Installation Instructions Manual Download Page 9

 

 

9 of 11 

 

MAINTENANCE FOR K-100 Adjust-A-Sink® 

 

BASIC FEATURES

The Adjust-a-Sink

®

 System elevates the Shampoo Bowl a total of 12”.  Distance 

from the floor to the top the of bowl ranges from approximately 34” to 46”.   A self contained, 
maintenance free foot-operated hydraulic lift provides the lift capacity needed to raise the shampoo 
bowl.  The hydraulic lift’s foot pedal is free to rotate approximately 90 degrees to the side anytime the 
operator requires.  Components are manufactured from the highest-grade materials and should 
provide years of trouble-free service. 
 
The “Adjust-a-Sink”

®

 warranty is two (2) years on all parts and five (5) years on the hydraulic pump. 

Altering the 3-Stage Telescopic Drain in any way voids its warranty. 
 
Save these installation instructions for future reference.  
 

IT IS VERY IMPORTANT TO HAVE THE “ADJUST-A-SINK”® INSTALLED CORRECTLY AND 
THE PLUMBING ALIGNED PERFECTLY.  NOT DOING SO COULD RESULT IN UNDUE 
PRESSURE ON VARIOUS COMPONENT PARTS AND COULD ALSO CAUSE THE PLUMBING 
TO LEAK. 

 

Lubrication:

 When the sink will not be in use for a period of time, or over night, lower the sink to its 

lowest position.  This allows the shaft to stay lubricated in the hydraulic fluid.  By doing this, it will 
maintain the smoothness of the elevation.  

NOTE: We recommend that you raise and lower the 

sink at least once daily to ensure proper lubrication all of critical components.

 

 

Cleaning

: after use or at the end of the day, wipe the shroud and pump with a clean damp cloth, mild 

cleaning solution or a stainless steel spray cleaner.  This will keep your unit looking new.   The 
shampoo sink should be cleaned on a regular basis as well, using a non-abrasive cleaner.  For those 
units equipped with a 

Hair Interceptor, 

we recommend that you open and clean it out every six 

months or sooner if sink use warrants. 
 
It is important to keep the nylon base (the base that the pump sits in) clean as well. The pump is 
designed to swivel, if it is not kept clean, it will eventually become hard to swivel the pump in the 
base. 
 

WITH PROPER CARE AND GOOD CLEANING THE “ADJUST-A-SINK”® WILL PROVIDE MANY 
YEARS OF SERVICE TO BOTH YOU AND YOUR CLIENTS. 
 
 
 
 

 

Summary of Contents for K100 Series













Reviews: