manualshive.com logo in svg

ADJ PAR Z MOVE, User Instructions

Share
Download
ADJ PAR Z MOVE User Instructions Download Page 20

ADJ Products, LLC  -  www.adj.com  - Par Z Move User Manual Page 19

  

Par Z Move

                                                                             

Operating Instructions

Gamma

 - In this menu you are able to make gamma corrections.

1.  Access the main menu and press the UP or DOWN buttons so that “Personality” is highlighted  

 

  then press ENTER.
2.  Use the UP or DOWN buttons to adjust the gamma brightness.
3.  Once you have found your desired setting press ENTER to confirm. 

Reset Motors

 - This will allow you to reset the pan/tilt motor, zoom motor, or all motors.

1.  Access the main menu and press the UP or DOWN buttons so that “Personality” is highlighted then   

  press ENTER. 
2. Press the UP or DOWN buttons until “Reset.Motor” is highlighted, then press ENTER.
3. Press the UP or DOWN buttons to find the motors you would like to reset.
4. Press the ENTER button to reset or press the MENU button to exit.

Display

 -

 

This submenu has four functions: (1). Adjust the display intensity (2). Invert the 

display (3). Activate and adjust the display screen blackout time (4). Activate and deactivate 

the display control panel lock.

1.  Access the main menu and press the UP or DOWN buttons so that “Personality” is highlighted then   

  press ENTER. 
2.  Use the UP or DOWN buttons to switch between “Intensity”, “Display Invert”, and “Screen  

 

  Saver Delay”. Press the ENTER button to select the setting you would like to adjust. 
3.  Use the UP or DOWN buttons to toggle between “ON” and “OFF” for each function.
 -  Intensity - Use the UP or DOWN buttons to adjust the display intensity between “1” being the    

  dimmest and “10” being the brightest. Press the ENTER button to confirm your adjustment.
 -  Display Invert - “YES” will invert the display, and “NO” will keep the display the same . Press the    

  ENTER button to confirm your adjustment.
 -  Screen Saver Delay - Use the UP or DOWN buttons to adjust the display intensity between “1”    

  being the dimmest and “10” being the brightest. Press the ENTER button to confirm your adjustment.
 -  Display Lock - “ON” will lock the display control after 30 seconds, and “OFF” will leave the display  

  control unlocked. To unlock the display press the MENU button for at least 5 seconds.
4.  Once you have found your desired settings press the ENTER button to confirm.

Summary of Contents for PAR Z MOVE































Reviews:

No comments

Brands by name

Popular brands

Load more brands