ADGT EDM106 User Manual Download Page 13

 

EDM Serial-to-Ethernet Converters 

User Guide ver. 2.0 | 2021-09-01 

 

 

Phone: +420 538 890 720 

13 

E-mail: [email protected] 

4.

 

In the RS-232 Settings and RS-485/RS-422 Settings menues, configure parameters of the serial 
ports in accordance with the settings of the connected equipment. For each port, select the 
operating mode Client or Server and set its parameters. 

Save changes using the Submit button. 

Table 6. Configuring serial ports.

 

Parameter 

Default value 

Possible values 

 

RS-232 

RS-485/RS-422 

 

State 

Enabled 

-------- 

Closed

 

in menu Home 

Disabled port 1 

and port 2 

-------- 

Disabled 

in menu Home 

RS-232: disabled/enabled 
RS-485: disabled port 1 and port 2/ 

              enabled port 1/ 

              enabled port 2/ 

              enabled port 1 and port 2 

RS-422: disabled port 1 and port 2/ 

              enabled port RS-422 

Operation mode “TCP-server” (default) 

 Port number 

60001 

RS-485(1): 60002 

RS-422: 60002 

RS-485(2): 60003 

Number of TCP-port of server 

List of allowed Client 

IP-addresses (IP1-IP5) 

0.0.0.0 

(“White” list disabled, 

all connections are allowed) 

“White” list of IP-addresses of clients (

up to 

5 addresses

), which are allowed to connect 

the converter, when it operates in the 

"Server" mode 

Maximum number of 

incoming connections 

2, 1 

Operation mode “TCP-client” 

Port number 

60001 

RS-485(1): 60002 

RS-422: 60002 

RS-485(2): 60003 

Port of TCP-server, to which the connection 

will be made 

Server IP address 

0.0.0.0 

(not specified) 

IP-address of server, to which the 

connection will be made 

Authorization type 

No authorization 

No authorization, ADGT  

Serial number 

Each port has its own serial number 

15-digit number for registration on the 

server (when choosing an authorization 

type ADGT) 

 

Clearing the input buffer 
on connection 

not clear 

not clear, clear 

Maximum TCP Packet 
Length  

1024 byte 

1 – 1024 byte 

Force Transmit Timeout 

10 ms 

1 – 10000 milliseconds 

Inactivity Time 

30 sec 

1 – 216000 seconds 

Ping IP Address 

0.0.0.0 

(connection check disabled) 

To enable connection check, specify the IP-
address to ping the connection (ICMP-echo)  

Ping Request Frequency 

30 sec 

10 seconds – 43200 seconds 

Flow Control 

Disabled 

 

Enabled, Disabled 

Baud Rate 

9600 

600-115200 bit/sec 

Data bits 

8, 7 

Parity 

No check 

Even, Odd, No check 

Stop bits 

1, 0.5, 1.5, 2 

Summary of Contents for EDM106




















Reviews: