background image

¬.9^l

K3897V1  8/02 

FOR DETAILS ON THE LIMITATIONS OF THE ENTIRE ALARM SYSTEM, REFER TO THE INSTALLATION 
INSTRUCTIONS FOR THE CONTROL PANEL WITH WHICH THIS DEVICE IS USED. 

 

FCC STATEMENT

 

This device complies with Part 15 of the FCC rules.  Operation is subject to the following two conditions:  (1) This device may not cause harmful interference, 
and (2) This device must accept any interference received, including interference that may cause undesired operation. 

FCC ID:  CFS8DL6128RF-2

 

 

FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT 

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: 

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's 
instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing 
device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a 
residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to 
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures: 

• 

If using an indoor antenna, have a quality outdoor antenna installed. 

• 

Reorient the receiving antenna until interference is reduced or eliminated.  

• 

Move the radio or television receiver away from the receiver/control. 

• 

Move the antenna leads away from any wire runs to the receiver/control. 

• 

Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits. 

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user or installer may find the 
following booklet prepared by the Federal Communications Commission helpful:  "Interference Handbook" 

This booklet is available from the U.S. Government Printing Office, Washington, DC 20402. 

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual.  Unauthorized 
changes or modifications could void the user's authority to operate the equipment. 

 

ADEMCO LIMITED WARRANTY 

Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates 
("Seller"), 165 Eileen Way, Syosset, New York 11791, warrants its products to be in conformance with its own plans and 
specifications and to be free from defects in materials and workmanship under normal use and service for 24 months 
from the date stamp control on the product or, for products not having an Ademco date stamp, for 12 months from date 
of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter 
period shall apply. Seller's obligation shall be limited to repairing or replacing, at its option, free of charge for materials 
or labor, any product which is proved not in compliance with Seller's specifications or proves defective in materials or 
workmanship under normal use and service. Seller shall have no obligation under this Limited Warranty or otherwise if 
the product is altered or improperly repaired or serviced by anyone other than Ademco factory service. For warranty 
service, return product transportation prepaid, to Ademco Factory Service, 170 Michael Drive, Syosset, New York 11791. 

THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A 
PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE 
HEREOF. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL 
DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER 
BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN 
NEGLIGENCE OR FAULT. 

Seller does not represent that the products it sells may not be compromised or circumvented; that the products will 
prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the products will in all cases 
provide adequate warning or protection. Customer understands that a properly installed and maintained alarm may 
only reduce the risk of a burglary, robbery, fire or other events occurring without providing an alarm, but it is not 
insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result. 
CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE 
OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS 
HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS 
LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY 
SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE 
COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty replaces any previous warranties and is 
the only warranty made by Seller on this product. No increase or alteration, written or verbal, of the obligations of this 
Limited Warranty is authorized. 

 
 
 

 

 
 
 

 
 
 
 
165 Eileen Way, Syosset, NY 11791 

Copyright 

 1999 PITTWAY CORPORATION 

Summary of Contents for 6128RF









Reviews: