background image

5

 

 

Introduction 

Meet the Ultra Alarm Control System 

Thank you for choosing to protect your premises with a 

Ultra-8/16

 of Australian Security

Supplies & ADC.

Ultra Alarm panel of Australian Security Supplies is a highly advanced, multifunction 
Wireless alarm control system, designed to flawlessly manage your security system at 
home or at business, protects you against burglary and supports the operation of 
electronic devices. 

The Ultra-8/16 has many incredible program options that can enhance the standard features 
of the panel from simple “Home Automation” to “Radio control” and Voice Prompted 
Command control”. Please ask your installer to find out more about these powerful 
features. 

You can phone your home to check or change the status of any output using the keys on 
your phone. Arm or disarm the whole house or just one area, all with  voice confirming 
your selections.  

Imagine turning on the spa before leaving work so it is hot when you get in the door. The 
under-floor heating has just automatically switched on using the on board timer and you 
have just opened the rollerdoor and disarmed the garage from your cell phone so the 
white ware repairman can work on your washer. 

It also has a comprehensive alarm event memory that stores all of the controller activity 
with the time and date. 

 

Typical Alarm System Configuration 

The protected premises can be divided up to 8 or 16 zones, as defined by the installation 
scheme.  The protected area can be grouped into 4 separate partitions (A,B,C,D).  The 
system can be grouped for User ‘s convenience to separate, in a business environment, 
the offices from the warehouse area, or in a private residence, the different rooms of the 
home, e.g., living room, bedroom, etc.  

Each zone can react differently to various events, to generate an alarm or activate a 
device. 

The system can be armed in two different modes: 
1) Arm –the protected areas are entirely vacated 
2) Stay –people and pets populate the protected areas. 

The User who has access to the keypad's control features, can change the settings. 

The system can be accessed via multiple keypads (each located at a different site).  Up 
to 8 keypads can be integrated into the system. Access levels and Users’ access codes 
are detailed below.  

 

 

Summary of Contents for Ultra-8/16




























Reviews: