ADC AD-120ES, Installation Manual, Page: 27 / 34

113386-28 www.adclaundry.com 27
TIMING LEGEND
SPIN TIME
Adjustment Position Number 1 2 3 4 5
Time in Seconds* 30 60 90 120 150
DWELL (STOP) TIME
Adjustment Position Number 1 2 3 4 5
Time in Seconds* 5 6.3 7.6 8.9 10.2
* Values shown are +/- 1-second.
Reversing Timer Spin / Dwell Adjustments
Timer models have an electronic reversing timer in the
electrical service box, which is located in the upper left rear
area of the dryer.
Both the Dwell (stop) Time and the tumbler Spin Time are
adjustable by mode selection switches located on the
electronic timer (as noted in the illustration below).
Preoperational Instructions _________
Phase 7 Dryers
The L.E.D. display reads “READY” (no cycle in progress).
Press the letter on the keypad corresponding to the cycle
desired (i.e., key “D”).
NOTE: “0-40” will require the “START/ENTER” key to be
pressed after the number is selected in order to accept the
selection and start drying.
The dryer will then start. (I.E., blower, tumbler, and heat.)
The L.E.D. display will read MANUAL DRYING CYCLE D,
00:00 MIN REMAIN.
NOTE: Press and hold the “UP ARROW” to view the tumbler
temperature at any time.
The dryer can be stopped at any time by pressing the “STOP/
CLEAR” key, at this time the dryer will go into a cycle pause.
If the “STOP/CLEAR” key is pressed again at this point, the
cycle that was in progress will be cancelled and returned to
the “READY” state.
Press and hold the “DOWN ARROW” to view the tumbler
RPM.
When the programmed drying time has expired, the Phase 7
non-coin microprocessor controller (computer) will proceed
into the Cool Down Cycle.
Once the Cool Down Cycle begins at the end of the heat
cycle, the L.E.D. display will read COOL DOWN TEMP ___/
___ MINUTES REMAINING. At the end of the heat cycle,
the dryer will shut off the heat and continue the fan and
tumbler until the Cool Down Time or temperature is reached.
IMPORTANT: For more detailed information regarding the
microprocessor controller (computer) on the dryer, refer to
the microprocessor user’s manual included with the dryer.
Phase 5 Dryers
Turn on electric power to the dryer.
Make sure the main door is closed and the lint drawer is
securely in place.
Microprocessor controller (computer) system operational test
to start dryer...
L.E.D. display will read “FILL.”
Press the “E” (preprogrammed) cycle key on the keypad.
L.E.D. display will quickly read: “Ld30,” “Lc04,” and “F180”
(unless special programs requested). These codes mean
that the dryer is in the timed mode and will operate with heat
of 180° F (82° C) for 30 minutes drying time and have a 4
minute cool down period.
Dryer will now start and the L.E.D. display will read “Dr30”
(dry mode for 30 minutes) and count down in minutes.
NOTE: The dryer can be stopped at any time by opening
main door or by pressing the “CLEAR/STOP” key. To restart
the dryer, press the “ENTER/START” key or preprogrammed
cycle key (i.e., “E”).
Pressing keypad key “A,” “B,” “C,” “D,” or “F” will also start
the dryer. The six preprogrammed drying cycles “A” through
“F” have been stored in the microprocessor controller’s
(computer’s) memory. Refer to the computer programming
manual supplied with this dryer for these preprogrammed
cycles.
Dual Timer Dryers
Turn drying timer knob for a time of 20 minutes.
Select “High Temp.”
Push “Push to Start” button.
To stop dryer, open the main door.
Spin and dwell (stop) times are adjustable at the reversing
timer.