ADB Safegate L-858 AGSF Series User Manual Download Page 54

Page: 54 / 56

A.2 Recycling

A.2.1 Local Authority Recycling

The disposal of ADB SAFEGATE products is to be made at an applicable collection point for the recycling of electrical and

electronic equipment. The correct disposal of equipment prevents any potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate waste handling. The recycling of materials helps to

conserve natural resources. For more detailed information about recycling of products, contact your local authority city office.

A.2.2 ADB SAFEGATE Recycling

ADB SAFEGATE is fully committed to environmentally-conscious manufacturing with strict monitoring of our own processes as

well as supplier components and sub-contractor operations. ADB SAFEGATE offers a recycling program for our products to all

customers worldwide, whether or not the products were sold within the EU.
ADB SAFEGATE products and/or specific electrical and electronic component parts which are fully removed/separated from

any customer equipment and returned will be accepted for our recycling program.
All items returned must be clearly labeled as follows:

•

For ROHS/WEEE Recycling

•

Sender contact information (Name, Business Address, Phone number).

•

Main Unit Serial Number.

ADB SAFEGATE will continue to monitor and update according for any future requirements for EU directives as and when EU

member states implement new regulations and or amendments. It is our aim to maintain our compliance plan and assist our

customers.

L-858 AGSF
SUPPORT

44
Copyright

Summary of Contents for L-858 AGSF Series





















































Search results

Summary of Contents for L-858 AGSF Series

Reviews:

Related manuals for L-858 AGSF Series

Brands by name

Popular brands

ADB Safegate L-858 AGSF Series, User Manual

Search results

Summary of Contents for L-858 AGSF Series

Reviews:

Related manuals for L-858 AGSF Series

Brands by name

Popular brands