Acute MSO 2000 Series Manual Download Page 41

Page: 41 / 60

皇晶科技股份有限公司

Acute Technology Inc.



2018

Stack DSO (Oscilloscope)

Install the special software provided by each oscilloscope brand to stack MSO and

oscilloscope. The software names are shown in the following table:

DSO brand

Software

Acute

Acute DSO software

Tektronix

Please download the

TEKVISA CONNECTIVITY SOFTWARE

from the Tektronix website.

Agilent

Keysight

Please download the

KEYSIGHT IO LIBRARIES SUITE

from the

Keysight website.

LeCroy

Please download the

NI VISA

and Drivers from the

website.

HAMEG

Please download the

NI VISA

and Drivers from the

website.

Rohde & Schwarz

Please download the

NI VISA

and Drivers from the

website.

Oscilloscope supportive models:

DSO brand

Model

USB

TCP/IP

Acute

DS-1000
TravelScope

Tektronix

TDS1000B/1000C/2000B/3000/3000B/
3000C/5000B/7000
DPO2000/3000/4000/4000B/5000/7000
7000C/70000/70000B
DSA70000/70000B
MSO2000/3000/4000/4000B/5000
MDO3000/4000
TPS2000/2000B

Agilent

DSO1000A/5000A/DSO6000A/6000L
7000A/7000B/9000A
MSO6000A/7000A/7000B/9000A
DSO-X 4000A /MSO-X 4000A
DSO-X 3000A /MSO-X 3000A
DSO-X 2000A/MSO-X 2000A

Keysight

DSO-X 3000T
MSO-X 3000T

LeCroy

WaveRunner / WaveSurfer / HDO4000 /
HDO6000 / SDA 8 Zi-A / DDA 8 Zi-A

HAMEG

HMO3000/2000/1000

R & S

RTO1000/RTE1000

Summary of Contents for MSO 2000 Series























































Search results

Summary of Contents for MSO 2000 Series

Reviews:

Brands by name

Popular brands

Acute MSO 2000 Series, Manual

Search results

Summary of Contents for MSO 2000 Series

Reviews:

Brands by name

Popular brands