Actuator Systems ReliTouch RT-201 Installation Manual Download | Manualshive

Page: 82 / 88

background image

http://www.advancedactuators.com

ReliTouch® User Manual

82

3.4 Unlocking the ReliTouch

®

RT-201 in 1:1 Mode with a

registered PIN Code

1) Enter the

specific User ID

on the keypad of the outside unit, Press

*

, Enter the

Registered PIN Code

and Press

**

.

2) If PIN Code verification was successful, two short beeps will be
heard, the green LED will flash and the ReliTouch

®

RT-201 will

unlock (and remain unlocked for approximately four seconds).

If verification of the registered PIN Code was not successful, the
LED will flash three times, three short beeps will be heard and the
ReliTouch

®

RT-201 will power off. Start over from the beginning

of this section. Also, check to make sure that the PIN Code being
used has been registered, AND make sure that the matching mode
is set to 1:N.

If LED flashes red once, and one single beep is heard after the PIN
code was successfully entered, this indicates that User ID
associated to the enrolled fingerprint is either outside of their
Timed Access settings, OR their User ID is set to INVALID, OR the
lock is set to INVALID.

www.BuilderDepot.com

«
...
80
81
82
83
84
...
»

Summary of Contents for ReliTouch RT-201

























































































Reviews:

No comments

Related manuals for ReliTouch RT-201

Brand: Comax Pages: 2

Brand: Classic Brass Pages: 2

DEADBOLT EDITION SECURE PGD728

Brand: Lockly Pages: 17

GATEMAN YDR2108

Brand: Yale Pages: 40

Corvan Entrance Lock Set

Brand: Lane Security Pages: 6

Brand: Yale Pages: 20

Brand: Iseo Pages: 30

Brand: La Gard Pages: 1

La Gard Reset Box

Brand: Dormakaba Pages: 2

AUDITCON 2 SERIES

Brand: Dormakaba Pages: 4

Brand: Dormakaba Pages: 8

Brand: Dormakaba Pages: 20

Brand: StGuchi Pages: 2

Brand: Accuride Pages: 3

Brand: Pamex Pages: 2

Brand: Waferlock Pages: 2

Brand: Bonaiti Pages: 2

Brand: HEOSolution Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands