Classic Brass
Manufacturers of Fine Solid Brass Hardware
P.O. Box 3563
Jamestown, New York 14702-3563
(800) 869-3173
Fax: (800) 215-2019
E-mail: [email protected]
Form 155, 16/June/04
Page 1 of 2
© Classic Brass, Inc. 2004
All rights reserved.
Any unauthorized reproduction is a violation of all applicable laws.
Lever/Lever, Knob/Knob Mortise Entry Set
Installation Instructions
PREPARE THE DOOR & FRAME:
I.
Prepare the door for installation according to the provided
drill and mortise instructions. It is important that you
confi rm all measurements prior to drilling the door!
II. Install the mortise lock body using two of the 12-24 x 7/8”
combination screws provided.
INSTALLING THE HARDWARE:
III. Slide the swivel spindle through the knob hole, making
sure the spindle notch is located on the exterior side of the
door and that both grooves are facing down. The lever
or knob set screw will seat in this groove.
IV. With the exterior plate held in position, install the mortise
cylinder by screwing it clockwise into the lock body until
tight and properly aligned. Use a key to test the function
of the lock.
V. Align the exterior plate with the edge of the door, then
taking care not to mark or scratch the plate, drill four
1/8” pilot holes for the fastening screws. Secure the exterior
plate to the door using the #6-32 x 1” screws provided.
VI. Slide the interior plate assembly into position with the
turnpiece stem seated within the lock body. Test the turn-
piece for proper functioning.
VII. Align the interior plate assembly with the edge of the door,
then taking care not to mark or scratch the plate, carefully
drill four pilot holes for the fastening screws. Secure the
plate to the door using the four #6-32 x 1” screws provided.
VIII. Seat the graphite washer on the base of the knob or lever,
then slide the knob/lever on the spindle until it sits against
the hub. Secure by tightening the 1/4-28 set screw with the
1/8” Allen wrench provided.
IX. Test the latching and locking mechanisms again, and once
your are satisfi ed that they are working properly, tighten
the two cylinder locking screws located in the face of the lock
body.
Install the lock face plate using the two #6-32 x 1/4”
screws provided.
X. Mortise the door frame and install the strike plate using two
of the 12-24 x 7/8” combination screws provided.
BILL OF MATERIAL:
__ (1) Mortise lock assembly,
Knob x knob/lever x lever
Includes:
__ (2) #12-24 x 7/8”
combination screws.
__ (1) Finished lock face plate.
Includes:
__ (2) Finished #6-32 x 1/4”
fl at head screws.
__ (1) Finished strike plate.
Includes:
__ (2) #12-24 x 7/8”
combination screws.
__ (1) Interior plate assembly.
Includes:
__ (1) Interior plate.
__ (1) Hub.
__ (1) Turnpiece w/ nylon
bushing and locking
washer.
__ (4) #6-32 x 1” screws.
__ (1) Exterior plate assembly.
Includes:
__ (1) Exterior plate.
__ (1) Hub.
__ (4) #6-32 x 1” screws.
__ (1) Swivel spindle.
__ (1) Mortise lock cylinder.
__ (2) Levers - One each left & right
Or
__ (2) Knobs.
Each Includes:
__ (1) 1/4-28 set screw.
__ (2) Graphite washers.
__ (1) 1/8” Allen wrench.
