background image

Operation Manual - Serene 2 Remote Controller

Document: 9590-4010  

 Ver. 1 200819

Operation Manual

Remote Controller

4

03.  Button and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The 
following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, 
refer to the 

Basic Functions

 section of this manual.  

1

ON/OF

This button turns the air conditioner On or Off. 

2

TEMP  UP 

 

Increases temperate in 0.5°C increments. Maximum 
temperature is 30°C.

3

SET

Scrolls through operation functions as follows: 
Breeze away 

 

  Active Clean 

    

 Fresh 

 

 Sleep 

 

 Follow Me 

 

 AP Mode 

 

 

Breeze away 

 

 ......

The selected symbol will flash on the display area, 
press the 

OK

 button to confirm.

4

TIMER

Set timer to turn unit On or Off.

5

TEMP DOWN  

Decreases temperature in 0.5

O

C increments. Min. 

temperature is 16

O

C.

6

FAN SPEED 

Selects fan speeds in the following order: Au (auto)

 

20% 

 40% 

 60% 

80% 

 100%.

7

Boost

Enables unit to reach preset temperature in shortest 
possible time

8

LED

Toggles the LED display and buzzer of the air 
conditioner buzzer to On and Off.

9

Humidity Mode

Adjust the room humidity during Dry in a range of 35% 
~ 85%. Press this button to increase the humidity in 5% 
increments.

NOTE:

 After setting, the humidity settings will display 

on the screen.

10

EGO/GEAR

Press this button to enter the energy efficient mode in 
a sequence of following:
ECO 

 GEAR (75%) 

 GEAR (50%) 

Previous 

setting mode 

 ECO ......

11

Swing

Starts and stops the horizontal louver movement. 
Hold down for 2 seconds to initiate vertical louver auto 
swing feature.

12

OK

Used to confirm the selected functions.

13

Eco Intelligent Eye

Used to detect the occupancy in the room to save 
energy.

14

Mode

Scrolls through operation modes as follows:   

AUTO 

 COOL 

 

DRY 

 HEAT 

 FAN 

 

AUTO

15

Screen

Displays the setting, indicators and operation 
conditions.

Humidity

Boost

1

2

5

14

12

11

6

7

8

13

10

9

15

4

3

Summary of Contents for Serene 2 RC-02

















Reviews: