ActronAir BMS MODBUS 485 Installation And Commissioning Manual Download Page 5 | Manualshive

Page: 5 / 24

background image

Installation and Commissioning Guide

ICUNO-MOD

5

4

Installation and Commissioning Guide ICUNO-MOD

Doc. No. 9590-3013

Ver. 5 200722

ActronAir is constantly seeking ways to improve the design of its products, therefore specifications are subject to change without notice.

Copyright © 2019 Actron Engineering Pty. Ltd.

03. ICUNO-MOD

The UNO Modbus RS-485 BMS Card allows the ActronAir Air Conditioners control system to interface with a BMS System.

The card allows communication from the UNO Outdoor Board to the customers’ BMS system through the Modbus RTU
protocol over RS-485. Each unit on the Modbus RS-485 network has a unique address.

ICUNO-MOD Cable Requirements

Recommended Cable Size: 0.5mm² (7/0.30)

Use two twisted pair shielded data cable to connect the data lines of the RS-485 bus

SW1-SERIAL

ADDRESS DIP

SWITCH

SW2-BMS

SETTINGS DIP

SWITCH

RESET

PUSH

BUTTON

SW3-TERMINATION

DIP SWITCH

STATUS

LEDS

BMS IN/OUT

CONNECTORS

OUTDOOR DATA

CONNECTOR

«
...
3
4
5
6
7
...
»

Summary of Contents for BMS MODBUS 485

























Reviews:

No comments

Related manuals for BMS MODBUS 485

Brand: Palm Pages: 14

Brand: Daikin Pages: 51

Brand: Toco Pages: 12

Brand: ABB Pages: 27

Brand: Canon Pages: 12

Brand: Banner Pages: 10

Brand: Fantasea Pages: 18

Brand: Fantasea Pages: 15

Brand: Zibro Pages: 2

Brand: QIMMIQ Pages: 16

Brand: QA1 Pages: 10

Brand: Xerox Pages: 10

Brand: Samsung Pages: 12

Brand: Samsung Pages: 24

Brand: Samsung Pages: 295

AW07A(G)2NBA/DE/EA

Brand: Samsung Pages: 16

Brand: Waldbeck Pages: 7

Aerasgard KCO2-W

Brand: S+S Regeltechnik Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands