Installation & Commissioning Guide - ESP Platinum ID Split Ducted Units
Doc. Part No. 0525-052
Rev. 4.0 180302
Page 2 of 16
TABLE OF CONTENTS
INTRODUCTION
CONGRATULATIONS
on your purchase of an Actron
Air Platinum Series air conditioning unit ! This unit has
been designed and engineered to provide optimum air
conditioning and to achieve maximum energy efficiency.
Your air conditioning system has been manufactured from
the highest quality materials. Numerous “in house” and
“external” inspection and test procedures were conducted
to your air conditioning to ensure satisfactory operation.
INFORMATION ABOUT THIS GUIDE
This guide provides installation instructions, specific
to your split ducted indoor unit. Read this manual
thoroughly and take into consideration all specifications
and instructions to insure correct installation and safe
operation of your air conditioning system.
Keep this document near the unit for future
reference. Ensure that all technicians that work
on the unit can refer to this manual at any time.
PRODUCT INSPECTIONS
Fully check your air conditioning unit and all items
against the bill of loading upon receiving your shipment.
Inspect the unit, components and accessories for any
sign of shipping damage. If there is any damage to the
unit, contact Actron Air Customer Care Department
immediately on:
1800 522 722.
Check the unit nameplate to verify the model, serial
number, electrical rated specifications and details are
correct.
CODES, REGULATIONS AND STANDARDS
The installer and/or contractor assumes responsibility
to ensure that unit installation complies with the
relevant council, state / federal codes, regulations and
building code standards. All electrical wiring must be in
accordance with current electrical authority regulations
and all wiring connections to be as per electrical diagram
provided with the unit.
SAFETY INSTRUCTIONS
1. Only licensed HVAC technicians
*
should install and
service this air conditioning equipment. Improper
service or alteration by unqualified technician could
result in significant and major damage to the product
or property which may render your warranty null
and void. Such unqualified service could also lead
to severe physical injury or death. Follow all safety
instructions in this literature and all warning labels
that are attached to the equipment.
2. Prevailing WH&S regulations must be observed
and will take precedence to the safety instructions
contained on this manual. Safe work practices and
environment must be the paramount importance in
the performance of all the service procedures.
3. Ensure that unit installation complies with relevant
council regulations and building code standards.
4. All electrical wiring must be in accordance with
current electrical authority regulations and all wiring
connections to be as per electrical diagram provided.
5.
Secure the fans against accidental contact. Beware
of pinch point and sharp edges which can cause
cutting injury.
6. Always wear appropriate PPE, remove any dangling
jewellery and protect long hair by wearing a cap.
7.
Make sure that safety guards and panel covers are
always firmly secured and not damaged.
8.
This appliance is not intended for use by young
children or infirm persons unless they have been
adequately supervised by a responsible person to
ensure that they can use the appliance safely. Young
children should be supervised to ensure that they do
not play with the appliance.
9.
Installer must incorporate a means of electrical
disconnection (isolator) in the sub mains fixed
wiring in accordance with the Australian wiring rule
(AS3000).
10. Secure the power cords and control cables that goes
in/out the unit. Use the cable ties provided in the
control box.
*
Qualifications required will be appropriate Electrical,
Refrigeration and Refrigerant Handling License & Training,
dependent on local State/Territory regulations.
This indoor unit is designed to match only with ActronAir
outdoor unit as specified in the Technical Selection
Catalogue.
This unit is designed for use with R410A refrigerant
only.
The unit is supplied with factory charged dry air. Beware
of the pressurised air charge when purging. Remove
the caps from the connection points and purge the
system only when the field pipes connection are ready
to be completed.
IMPORTANT NOTES TO THE INSTALLER
Introduction ....................................................................
Safety Instructions..........................................................
Components Overview...................................................
Unit Dimensions and Clearances ..................................
Two-Piece Fan Coil .......................................................
Installation Instructions .................................................
Unit Lifting Procedures ..................................................
Condensate & Safety Tray Drainage Instructions .........
Zone Barrels Mounting Instructions ..............................
Wiring Diagram..............................................................
Maximum Cable Lengths...............................................
Maintenance Frequency Checklist ................................
Key Parts List ................................................................
2
2
3
4
6
7
8
9
10
11
12
14
15
