ACTi KCM-5*11E Installation Manual Download

Page: 2 / 19

www.acti.com

Installation Guide

Table of Contents

Installation Procedures ..................................................... 3

Step 1: Install the Bracket ......................................................................... 3

Step 2: Remove the Back Cover ............................................................... 4

Step 3: Prepare the Flex Conduit ............................................................. 4

Step 4: Connect the Ethernet Cable ......................................................... 7

Step 5: Install the Camera ......................................................................... 8

Step 7: Access the Camera Live View ................................................... 10

Appendices ....................................................................... 11

Connecting a Power Adaptor (Optional) ................................................. 11

Connecting DI/DO Devices (Optional) .................................................... 13

Connecting a Serial Device (Optional) ................................................... 16

Safety Information ............................................................ 18

Summary of Contents for KCM-5*11E




















Search results

Summary of Contents for KCM-5*11E

Reviews:

Related manuals for KCM-5*11E

Brands by name

Popular brands

ACTi KCM-5*11E, Installation Manual

Search results

Summary of Contents for KCM-5*11E

Reviews:

Related manuals for KCM-5*11E

Brands by name

Popular brands