manualshive.com logo in svg

ACT ACTENTRY V-IP, Operating And Installtion Instructions, Page: 4 / 30

Share
Download
ACT ACTENTRY V-IP Operating And Installtion Instructions Download Page 4

ACTentry V-IP Operating and Installation Manual 

 

 

Page 3

 

 

 

 

Ordering Information 

 

ACT Product Code

Product description

ACTentry V-IP SK 

Surface Mount Kit*

ACTentry V-IP FK 

Flush Mount Kit*

ACTentry V-IP SP

VoIP Door Entry Panel (surface )

ACTentry V-IP FP

VoIP Door Entry Panel (flush )

ACTentry V-IP SKX

Surface Mount Kit**

ACTentry V-IP FKX

Flush Mount Kit**

ACTentry V-IP SPX

VoIP Door Entry Panel (surface) with cut out for
panel mount proximity reader

ACTentry V-IP FPX

VoIP Door Entry Panel (flush) with cut out for panel
mount proximity reader

ACTentry V-IP CTR

V-IP control unit 

ACTentry V-IP PCH 

Plug in PC Handset. Internal use only.

ACTentry V-IP PSU

1Amp Power Supply Unit.

* 

Vandal resistant VoIP Door Entry Panel, PC handset, Control Unit & Power Supply 

** 

Extended Version: 

Vandal resistant VoIP Door Entry Panel with cut-out for panel-

mount proximity reader,  PC handset, Control Unit & Power Supply.

 

 

Product Specification 

 

Supply Voltage

10-15Volts DC

Current Consumption

600mA 

Operating Temperature

-10  to +50 degrees C

Door Open Time

1 – 255 seconds (4 minutes and 15 seconds 
maximum) 

Relay Contact Rating 

Lock Relay 5A / 50Vac, Alarm Relay 1A / 
50Vac, Buzzer Relay 1A/ 50Vac
Flush Mount:         243.5 X 125 mm
Surface Mount:     266.5 X 124 mm

Distance from V-IP controller 
to Door Entry Panel

50m

Water Resistance

Medium IP54

Entrance Panel Size                                             

 

 

 

Summary of Contents for ACTENTRY V-IP































Reviews:

No comments