Acromag ES2163, User Manual, Page: 5 / 94

EtherStax™ ES2163/2164 User’s Manual Modbus TCP/UDP/IP Analog Input
___________________________________________________________________
_______________________________________________________________________________________
Acromag, Inc. Tel:248-295-0880 Fax:248-624-9234 Email:
sales@acromag.com http://www.acromag.com
5
ESA-DIN-VMK TOP VIEW
NOTE: ESA-DIN-VMK CONTAINS
TWO OF THESE PIECES.
ESA-DIN-VMK SIDE VIEW
7.625
GROUND
SCREW
8.226
2.444
6.125
GROUND
SCREW
GROUND
SCREW
DIMENSIONS ARE IN INCHES.
THE ES2163/2164 IS SHOWN AT LEFT.
ETHERSTAX DIMENSIONS
A SINGLE UNIT STANDS 2.444 INCHES TALL.
EACH ADDITIONAL UNIT ADDS 2.229 INCHES.
A TWO UNIT STACK IS 4.673 TALL.
A THREE UNIT STACK IS 6.902 TALL.
THE OPTIONAL SURFACE-MOUNT BASE-PLATE
ESA-SMK ADDS 0.25" TO HEIGHT.
THE OPTIONAL DIN RAIL CLIP ESA-DIN-VMK
ADDS 1.0" TO HEIGHT WHEN MOUNTED ON
35mm x15mm DIN RAIL.
THE OPTIONAL BASEPLATE AND HEAVY DUTY
DIN RAIL MOUNT ESA-DIN-HMK ADDS 0.84" TO
HEIGHT WHEN MOUNTED ON 35mm x15mm DIN RAIL.
Units are designed to interlock and stack together up to three units high. A
stack of units can be bolted to a wall or flat surface, or mounted on deep-
channel, “T” type, 35mm x15mm DIN rails (per DIN EN60715 TH35),
depending on the optional mounting kit selected. Available mounting kits are
shown below.
DIN Rail Vertical Mount Kit ESA-DIN-VMK (One or Two Units):
This kit
includes two plastic DIN clips (Rose Bopla #77003500) that slide into the
dove-tail channel of the bottom of the housing. You can use one clip to
mount a single unit, or both for added stability when stacking two units. If
stacking more than two units on a DIN rail, see ESA-DIN-HMK.
08 10 12
TS1
14 C
24 26 28 30 C
1 2
00 02 04 06 C 16 18 20 22 C
PORT 1 PORT 2
RST
09 11 13 15
25 27 29
TS2
31
DFT
01
TOP
03 05 07 17 19 21 23
STATUS
ETHERNET 10/100M
TOP should coincide with
the upper lip of the DIN rail
This side of clip should
align with top of rail
COM
UPWARD
Position clip such that TOP is aligned
with end of unit you want upright.
Acromag
DIN MTG CLIP
OF ESA-DIN-VMK
TO REMOVE: Push unit upward and tilt TOP of
unit back towards you to disengage it from rail.
TO HANG: Tilt unit and place TOP of clip over upper lip
of DIN rail. Press bottom towards rail to snap in place.
MOUNTING AND
DIMENSIONS
These Models are open-type
devices and intended for
installation into a suitable
enclosure by the end-user.
It is recommended that
enclosed units be panel-
mounted with the vented
endplates positioned at top
and bottom for improved
cooling. Review the Operating
Ambient Temperature
specification for more
information.
A single unit stands 2.444
inches tall. Each additional
unit adds 2.229 inches.
A two-unit stack would be
4.673 inches tall. A three unit
stack is 6.902 inches tall. Add
any additional height as
necessary to account for the
mounting plate, DIN clip, and
DIN rail, if required.