manualshive.com logo in svg

ACP OmniSWD, User Manual, Page: 23 / 34

Share
Download
ACP OmniSWD User Manual Download Page 23

OMNISWD

®

 USER MANUAL 

 

21 

COPYRIGHT © 2019-2020, ACCELERATED CARE PLUS CORP., ALL RIGHTS RESERVED 

Safety Features / Error Messages 

The OmniSWD

®

 is microprocessor controlled; it continually “self-checks” the operation of the system.  If an error in 

the function of the microprocessor is detected the shortwave power will be immediately turned off and the word FAIL 
will be shown on the display. If the unit repeatedly fails after cycling the power, then qualified service personnel should 
be called. The unit incorporates a safety mechanism in case of overheating. If the unit overheats the treatment is 
automatically stopped, the buzzer sounds intermittently, and “HOT” is shown on the display. 

 

Coaxial Cable - Applicator Head  
Error Warning 

This pop-up window appears if a treatment is attempted 
without the applicator being plugged in (or if the 
cable/applicator is damaged). It will also appear if a fault 
occurs in the cable or applicator during a treatment. 

 

Treatment will be prevented from starting unless a 
functioning applicator/cable combination is plugged in. 
 
If it persists, then contact ACP Customer Support at  
(1-800-350-1100). 

 

System Fault Warning                       

      

 

Service Due Pop-Up 

 

 

 
 

This is just a message that appear as a flag from 
the hours of use. The message is not an indication 
that something is wrong with your operating 
system or device. For service please contact  
ACP Customer Service at 1-800-350-1100 ext.3. 
Process to Reset the Service Due Timer: 

1.   Start the system 

2.   Go to settings 
3.   Go to maintenance 
4.   Insert the password: 12341924 and save 
5.   Go to service date 
6.   

Press reset hours counter and confirm

 

This pop-up window appears if the machine detects a 
communications error between its two processors. This 
should be a very rare event if it happens at all, and may 
not recur if the mains power is switched off and on 
again. If it persists, then contact ACP Customer 
Support at (1-800-350-1100).

   

Summary of Contents for OmniSWD



































Reviews:

No comments