background image

Important Safety Information

©2010 ACP inc.

 16400009 

7

Precautions to be observed before and during 

servicing to avoid possible exposure to excessive 

microwave energy, or electrical shock disconnect 

power to oven.

•  Do not operate or allow oven to be operated with 

door open.

•  Make the following safety checks on all ovens to be 

serviced before activating the magnetron or other 

microwave source, and make repairs as necessary:

•  Interlock operation
•  Proper door closing
•  Seal and sealing surfaces (arcing, wear, and 

 

other damage)

•  Damage to or loosening of hinges and latches
•  Evidence of dropping or abuse 

•  Before turning on microwave power for any service 

test or inspection within the microwave generating 

compartments, check the magnetron, waveguide or 

transmission line, and cavity for proper alignment, 

integrity, and connections.

•  Any failed or misadjusted components in the 

interlock, monitor, door seal, and microwave 

generation and transmission systems shall be 

repaired, replaced or adjusted by procedures 

described in this manual before oven is released to 

the consumer.

•  Check microwave leakage to verify compliance 

with the federal performance standard should be 

performed on each oven prior to release to the 

consumer.

To avoid risk of electrical shock, injury or death; make 

sure these grounding instructions are followed.

Grounding Instructions

WARNING

Do not remove grounding prong when installing 

grounded appliance in a home or business that does 

not have three wire grounding receptacle, under no 

condition is grounding prong to be cut off or removed. 

It is the personal responsibility of the consumer to 

contact a qualified electrician and have properly 

grounded three prong wall receptacle installed in 

accordance with appropriate electrical codes.

WARNING

To avoid the risk of electrical shock or death, do not 

alter the plug.  

WARNING

To avoid the risk of electrical shock or death,  this 

equipment must be grounded.

This  equipment 

MUST

 be grounded. In the event of 

an electrical short circuit, grounding reduces the risk 

of electric shock by providing an escape wire for the 

electric current. This oven is equipped with a cord having 

a grounding wire with a grounding plug. The plug must 

be plugged into an outlet that is properly installed and 

grounded. 

Consult a qualified electrician or servicer if grounding 

instructions are not completely understood, or if doubt 

exists as to whether the equipment is properly grounded.
Do not use an extension cord.  If the product power 

cord is too short, have a qualified electrician install a 

three-slot receptacle. This oven should be plugged into 

a separate 60 hertz circuit with the electrical rating as 

shown in the appropriate drawing. Models operate with 

a 120 supply voltage. When a microwave oven is on 

a circuit with other equipment, an increase in cooking 

times may be required and fuses can be blown.

NEMA 5-15R/5-15P  

120V–15AMP

Summary of Contents for MCS10DS

































Reviews: