ACP MCS10DS Service Manual Download Page 28

Page: 28 / 32

Disassembly Procedures

To avoid the risk of electrical shock, personal injury, or death,

disconnect power to oven and discharge the capacitors before

following any disassembly procedure.

28 16400009

5. Remove screws securing choke assembly to outer

door panel.

NOTE:

When disassembling door, use caution to

prevent deformation of slats on door frame/

choke assembly.

6. Begin at hinge side of door near bottom, insert

flat blade screwdriver between door frame/choke

assembly and outer door panel. Gently pry outer

door panel away from door frame to release tabs.

Work in clockwise direction to remove door frame.

7. Remove spring from hinge assembly.

8. Remove screws securing hinge assembly to choke

assembly.

9. Reassemble in reverse order.

A microwave leakage test must be performed anytime

a door assembly is removed, replaced, disassembly,

or adjusted for any reason.

Door Assembly

A microwave leakage test must be performed anytime

a door assembly is removed, replaced, disassembled,

or adjusted for any reason.

Door Removal

1. Disconnect power to oven.

2. Remove outer case, see "Outer Case" procedure.

3. Remove screws securing top hinge stopper to unit

cavity.

4. Remove oven door assembly from unit.

5. Reassemble in reverse order.

Door Disassembly

1. Disconnect power to oven.

2. Remove oven door, see "Door Removal" procedure.

3. Begin at the bottom of the door near hinge, insert flat

blade screwdriver between choke cover and outer

door panel. Gently pry upward on choke cover to

release tabs. Work in clockwise direction to remove

choke cover.

To avoid property damage, care must be taken when

prying choke cover from oven door.

4. Slide latch assembly downward and pull away from

door frame to release.

CAUT ION

Summary of Contents for MCS10DS

































Search results

Summary of Contents for MCS10DS

Reviews:

Related manuals for MCS10DS

Brands by name

Popular brands

ACP MCS10DS, Service Manual

Search results

Summary of Contents for MCS10DS

Reviews:

Related manuals for MCS10DS

Brands by name

Popular brands