ACP MCS10DS Service Manual Download Page 32

Page: 32 / 32

Disassembly Procedures

To avoid the risk of electrical shock, personal injury, or death,

disconnect power to oven and discharge the capacitors before

following any disassembly procedure.

32 16400009

Stirrer Motor

1. Disconnect power to oven.

2. Remove outer case.

3. Disconnect wire terminals from stirrer motor.

4. Remove screws securing stirrer motor to supporting

bracket.

5. Replace component and reverse procedure to

reassemble.

NOTE:

When replacing stirrer motor, verify motor shaft

is aligned with antenna shaft before securing

with screws.

Magnetron Thermal Cut-Out (Mag TCO)

1. Disconnect power to unit.

2. Remove outer case, see "Outer Case" procedure.

3. Disconnect wire terminals from TCO.

4. Remove screws securing TCO to magnetron.

5. Replace component and reverse procedure to

reassemble.

NOTE:

When reconnecting wiring to thermal fuses the

connectors must be tight.

Cavity Thermal Fuse

1. Disconnect power to unit.

2. Remove outer case, see "Outer Case" procedure.

3. Disconnect wire terminals from thermal fuse.

4. Remove screw securing thermal fuse to oven cavity.

5. Replace component and reverse procedure to

reassemble.

NOTE:

When reconnecting wiring to thermal fuse the

connectors must be tight.

Tray Replacement

1. Unplug oven from outlet.

2. Using a suction cup or a thin bladed screwdriver, pry

upward on front corners and remove tray from unit.

3. Thoroughly clean and degrease sump area.

4. Clean oven cavity bottom where new oven tray will

make contact using mineral spirits or any

nonflammable degreasing solvent.

NOTE:

Detergents, soap, and water are not sufficient to

remove oil and grease.

5. Place new tray into unit.

Oven Light Assembly

The light bulb for inside of the oven can be changed only

by removing the outer case.

Follow these steps to change the bulb:

1. Disconnect power to unit.

2. Remove outer case, see "Outer Case" procedure.

3. Remove interlock assembly, see "Interlock Assembly"

procedure steps 1 through 4.

4. Disconnect wire terminals from oven light socket.

5. Push securing tab to release oven light asseembly

and lift upward to remove from interlock assembly

bracket.

6. Replace component and reverse procedure to

reassemble.

NOTE:

After replacing the oven light assembly. Verify

the "Interlock Assembly" is properly aligned and

operating correctly.

Air Guide

1. Disconnect power to unit.

2. Remove outer case, see "Outer Case" procedure.

3. Release plastic tabs securing top portion of light

cover to inner cavity side wall.

4. Lift upward on light cover to release bottom securing

tabs.

5. Replace component and reverse procedure to

reassemble.

Summary of Contents for MCS10DS

































Search results

Summary of Contents for MCS10DS

Reviews:

Related manuals for MCS10DS

Brands by name

Popular brands

ACP MCS10DS, Service Manual

Search results

Summary of Contents for MCS10DS

Reviews:

Related manuals for MCS10DS

Brands by name

Popular brands