ACME CETUS User Manual Download | Manualshive

Page: 32 / 36

background image

24. ArmFan5 Start Err

Check if the fan is not running.
Check if the fan leads are installed in place or disconnected.
Check if the fan is damaged.
Check if there are other interference items in the fan operating range.

25. ArmFan5 Stop Err

Check if the fan circuit on the motherboard breaks down.
Check if the component is damaged.

26. ArmFan5 Too Low

Check if the fan is out of order.
Check if there are other interference items in the fan operating range.

27. ArmFan5 Too High

Check if the fan is out of order.
Check if the fan circuit on the motherboard breaks down.

28. Lamp Hot Power Off

Check if the temperature switch of the lamp is off.
Check if the fans are still running properly.

29. Gravity Sensor Error

Check if the gravity sensor on board E is damaged.

30. Lamp Maintenance

Check lamp use time and replace the lamp in time.

31G

«
...
30
31
32
33
34
...
»

Summary of Contents for CETUS





































Reviews:

No comments

Related manuals for CETUS

Brand: JB-Lighting Pages: 40

Brand: Tascam Pages: 128

Brand: ParaBody Pages: 6

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: Idmed Pages: 2

Brand: Kamikaze Pages: 112

Brand: KAM Pages: 2

Brand: Ultraflex Pages: 3

9NP-B7524 Series

Brand: Nautilus Pages: 2

Be strong NS 700X

Brand: Nautilus Pages: 34

Brand: Nautilus Pages: 21

Brand: Valmar Pages: 78

Brand: Valhalla Scientific Pages: 64

Brand: rbd instruments Pages: 18

TOBIAS W775A03BKG

Brand: Home Decorators Collection Pages: 14

Brand: DC Med Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands