ACME CETUS User Manual Download

Page: 21 / 36

Prism1

Enter offset mode, Select

Prism1

, press the

ENTER

button to confirm, the present position will blink

on the display, use the

DOWN

button to offset the value from -128 to 127, press the

ENTER

button to store. Press the

MENU

button to exit.

R-Prism1

Enter offset mode, Select

R-Prism1

, press the

ENTER

button to confirm, the present position will

blink on the display, use the

DOWN

button to offset the value from -128 to 127, press the

ENTER

button to store. Press the

MENU

button to exit.

Prism 2

Enter offset mode, Select

Prism 2

, press the

ENTER

button to confirm, the present position will blink

on the display, use the

DOWN

button to offset the value from -128 to 127, press the

ENTER

button to store. Press the

MENU

button to exit.

R-Prism 2

Enter offset mode, Select

R-Prism 2

, press the

ENTER

button to confirm, the present position will

blink on the display, use the

DOWN

button to offset the value from -128 to 127, press the

ENTER

button to store. Press the

MENU

button to exit.

Focus

Enter offset mode, Select

Focus

, press the

ENTER

button to confirm, the present position will blink

on the display, use the

DOWN

button to offset the value from -128 to 127, press the

ENTER

button to store. Press the

MENU

button to exit.

Frost

Enter offset mode, Select

Frost

, press the

ENTER

button to confirm, the present position will blink

on the display, use the

DOWN

button to offset the value from -128 to 127, press the

ENTER

button to store. Press the

MENU

button to exit.

20G

Summary of Contents for CETUS





































Search results

Summary of Contents for CETUS

Reviews:

Related manuals for CETUS

Brands by name

Popular brands

ACME CETUS, User Manual

Search results

Summary of Contents for CETUS

Reviews:

Related manuals for CETUS

Brands by name

Popular brands