ACME CETUS User Manual Download | Manualshive

Page: 31 / 36

background image

16. LampFan1/2/4 Start Err

Check if the fan is not running.
Check if the fan leads are installed in place or disconnected.
Check if the fan is damaged.
Check if there are other interference items in the fan operating range.

17. LampFan1/2/4 Stop Err

Check if the fan circuit on the motherboard breaks down.
Check if the component is damaged.

18. LampFan1/2/4 Too Low

Check if the fan is out of order.
Check if there are other interference items in the fan operating range.

19. LampFan1/2/4 Too High

Check if the fan is out of order.
Check if the fan circuit on the motherboard breaks down.

20. StrobeFan3 Start Err

Check if the fan is not running.
Check if the fan leads are installed in place or disconnected.
Check if the fan is damaged.
Check if there are other interference items in the fan operating range.

21. StrobeFan3 Stop Err

Check if the fan circuit on the motherboard breaks down.
Check if the component is damaged.

22. StrobeFan3 Too Low

Check if the fan is out of order.
Check if there are other interference items in the fan operating range.

23. StrobeFan3 Too High

Check if the fan is out of order.
Check if the fan circuit on the motherboard breaks down.

30G

«
...
29
30
31
32
33
...
»

Summary of Contents for CETUS





































Reviews:

No comments

Related manuals for CETUS

SafetuNet Alert

Brand: Masimo Pages: 2

AJSPD850P - P2 DECK

Brand: Panasonic Pages: 73

Brand: Far Tools Pages: 25

Brand: ParaBody Pages: 3

Brand: Valiani Pages: 66

Brand: Yamaha Pages: 31

Brand: Yuwell Pages: 2

Brand: B&G Pages: 16

accumet BASIC AB 15

Brand: Fisher Scientific Pages: 56

Brand: Lievers Pages: 20

Brand: MyLight Pages: 2

Brand: Specac Pages: 43

Brand: Xantech Pages: 4

Brand: Desisti Pages: 11

Brand: Sygonix Pages: 8

BinTrac HouseLINK HL-10P

Brand: herdstar Pages: 8

Brand: Pepperl+Fuchs Pages: 60

LI2606.000 Series

Brand: Handicare Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands