TABLE 3:
VOLTAGE OUTPUT RANGE
Automation Components, Inc.
2305 Pleasant View Road | Middleton, WI 53562
Phone:
1-888-967-5224 |
Website:
workaci.com
Page 4
Version: 9.0
I0000585
OUTPUT DIP SWITCH
1, 2, 4, 5 ON…………… all others off
1, 3, 4,6 ON……………..all others off
4, 5 ON………………..all others off
1,4, 7 ON.....................all others off
VOLTAGE OUTPUT
0 – 5 V
1 – 5 V
0 - 10 V
2 – 10 V
TABLE 5:
PRESET OUTPUT SPANS
OUTPUT DIP SWITCH
1,2,3,4 ON…………… 1, 2, 3, 4 ON
2,3,4 ON…………….. 1 OFF
1,3,4 ON……………… 2 OFF
1,2,4 ON..................... 3 OFF
3,4 ON……………...1,2 OFF
2,4 ON……………...1,3 OFF
1,4 ON……………...2,3 OFF
4 ON………………..1,2,3 OFF
1,2,3 ON…………...4 OFF
None ON…………..1,2,3,4 OFF
1,2,3 ON…………...4 OFF
VOLTAGE OUTPUT
1V or 4mA
3V or 12mA
4V or 16mA
5V or 20mA
6V
7V
8V
10V
Adj. 1 – 11V
Adj. 10 – 20V
Adj. 4 – 20mA
TABLE 4:
CURRENT OUTPUT RANGE
OUTPUT DIP SWITCH
1, 2, 4, 5 ON…………… all others off
1, 3, 4,6 ON……………..all others off
VOLTAGE OUTPUT
0 – 20 mA
4 - 20 mA
CALIBRATIONS OF INPUT SIGNAL OTHER THAN PRESETS SHOWN ON TABLE
1.) If you have an input range other than any presets shown above, set the input DIP switches to one of the
three Adj. settings. See inputs above in bold type.
2.) Apply the maximum of the input signal to terminals IN and COM. With a volt meter measure the voltage
from TP1 to the AIM2’s input side common (COM). Turn the input Max. pot until the meter reads 5.00 ± 0.00
V. The maximum of the input signal is now calibrated.
3.) If the minimum of the input signal is zero, set input DIP switches 7 and 8 OFF and 6 ON.
4.) If the minimum of the input signal is other than zero, set maximum as in step 2, and use the following
steps to set the minimum:
A.) Set switch 8 ON and 6 and 7 OFF.
B.) Produce the minimum signal value at the input terminal (IN).
C.) Measure the voltage between the TP1 test point and COM. Record or remember.
D.) Now measure voltage between the TP3 test point and COM. Adjust the input MIN pot until the
voltage at TP3 is equal to the voltage recorded at TP1. The minimum and maximum input signals are
now calibrated.
SETTING AIM2 OUTPUT
FOR PRESET VOLTAGE OUTPUT RANGES:
Make the following switch settings on output DIP switches.
Set jumper J4 for E/Isnk (voltage/current sink), and J5 for SRC (source) output signal. See
Table 3
.
FOR PRESET CURRENT OUTPUT RANGES:
Make the following switch settings on output DIP switch. If
Source, set Jumper J4 to I and J5 to SRC. If Sink, set J4 to E/Isnk, and J5 to SNK. See
Table 4
.
FOR CALIBRATION OF AN ODD OUTPUT SIGNAL
Before proceeding, you must have already set up the
input signal. If not, return to page 3 and “SETTING
AIM2 INPUT”.
Output ranges are selectable on the output DIP
switch by setting offset (minimum signal) and spans
available (maximum minus offset) are shown below.
Find out if you can use a preset range by subtracting
the minimum output signal (or offset) from the
maximum. For example, a 3.4 to 9.4 V signal output
equals a 6 volt range, which is available as a preset,
and the 3.4 volt offset can be adjusted. Any span not
listed below will have to be set from one of the
adjustable range switch settings.
TO SET PRESET OUTPUT SPANS (Reference only
switches 1 through 4, others are for OFFSET - See
Table 5
).
