background image

PRODUCT SPECIFICATIONS

Automation Components, Inc.

2305 Pleasant View Road  |  Middleton, WI 53562

Phone:

 1-888-967-5224  |  

Website:

 workaci.com

Page 6

Version: 9.0

I0000585

WARRANTY

The AIM2 Series is covered by ACI’s Two (2) Year Limited Warranty, which is located in the front of ACI’S SENSORS & 
TRANSMITTERS CATALOG or can be found on ACI’s website: www.workaci.com.

24 VAC (+/- 10%), 50/60 Hz 

200 mA maximum 

0-5V, 0-10V, 0-15V, 0-20V, 1-5V, 2-10V, 3-15V, 4-20V, 0-1V

0-20 mA, 4-20 mA, 0-1 mA

1 VDC (Minimum) to 20 VDC (Maximum)

From 0 to 20 VDC

4 mA (Minimum) to 20 mA (Maximum)

From 0 to 20 mA

9,500Ω 

250Ω +/-1%

0-5 VDC, 1-5 VDC, 0-10 VDC, 2-10 VDC

0-20 mA, 4-20 mA

1 VDC (Minimum) to 20 VDC +/- 1 VDC (Maximum)

From 0 to 10 VDC

0 mA (Minimum) to 20 mA (Maximum)

From 0 to 20 mA

5,000Ω 

500Ω

+/- 3%

+/- 1%

45° Captive screw Terminal Blocks

12 (3.31 mm2) to 22 AWG (0.33 mm2)

0.5 Nm (Minimum); 0.6 Nm (Maximum)

35 to 120°F (1.7 to 48.9°C)

10 to 95% non-condensing 

-20 to 150°F (-28.9 to 65.5°C)

NON-SPECIFIC INFORMATION

 

Supply Voltage:

Supply Current: 

Input Voltage Signal Preset Ranges:

Input Current Signal Preset Ranges:

Input Signal Adjustable Voltage 

Span:

Input Signal Adjustable Voltage 

Offset:

Input Signal Adjustable Current 

Span:

Current Offset:

Input Voltage Impedance:

Input Current Impedance:

Output Voltage Signal Preset 

Ranges:

Output Current Signal Preset 

Ranges:

Output Signal Adjustable Voltage 

Span:

Output Signal Adjustable Voltage 

Offset:

Output Signal Adjustable Current 

Span:

Output Signal Adjustable Current 

Offset:

Output Voltage Impedance:

Output Current Impedance:

Accuracy:

Linearity:

Connections:

Wire Size:

Terminal Block Torque Rating:

Operating Temperature Range:

Operating Humidity Range:

Storage Temperature:

Summary of Contents for AIM2









Reviews: