background image

Chapter 4

74

Memory Size Has Changed Since Last Boot

In EISA mode, use Configuration Utility to reconfigure the 
memory configuration. In ISA mode, enter 

Setup

 and enter 

the 

new memory size

 in the memory fields.

Memory Verify Error

Use this location along with your system’s memory map to 
locate the bad chip.

Offending Address Not Found

This message is used in conjunction with the I/O 
CHANNEL CHECK and RAM PARITY ERROR messages 
when the segment that has caused problem cannot be 
isolated.

Offending Segment

This message is used in conjunction with the I/O 
CHANNEL CHECK and RAM PARITY ERROR messages 
when the segment that has caused problem cannot be 
isolated.

Press A Key To Reboot

 Press any key and the system will reboot.

Press

 F1

 to Disable NMI, 

F2

 to Reboot

When the BIOS detects a Non-maskable Interrupt 
condition during boot, this will allow you to disable the NMI 
and continue to boot, or you can reboot the system with the 
NMI enabled.

RAM Parity Error

Checking for segment

System Halted

Press CTRL + 

ALT + 

DEL to reboot.

Or plug out AC and wait for 10 seconds, then plug in AC 
again. Press power button to boot the system again.

Floppy Disk(s) Fail(80)

Unable to reset floppy subsystem

Floppy Disk(s) Fail (40)

Floppy Type mismatch

Hard Disk(s) Fail (80)

HDD reset failed

Hard Disk(s) Fail (40)

HDD controller diagnostics failed

Hard Disk(s) Fail (20)

HDD initialization error

Hard Disk(s) Fail (10)

Unable to recalibrate fixed disk

Hard Disk(s) Fail (08)

Sector Verify failed

Keyboard Is Locked Out

Unlock the key

Keyboard Error Or No Keyboard Present

Make sure the keyboard is attached correctly and no keys 
are pressed during the boot.

Manufacturing POST loop

System will repeat POST procedure infinitely while the P15 
of keyboard controller is pull low. This is also used for M/B 
burn in test.

BIOS ROM Checksum Error

BIOS will boot from the boot block and read BIOS binary 
file from FDD disk, then flash BIOS ROM (FWH - Firmware 
Hub).

Memory Test Fail

BIOS reports the memory test fail if the onboard memory is 
tested error

BIOS Messages

Action/FRU

Summary of Contents for Veriton 5200D





















































































































Reviews: