818~2040PD
40
5-4-1 ALARM MESSAGE
ALARM
NO.
ALARM
MESSAGE
CORRECTION
001
Y-axis stepping motor is overheat
Check if there is any obstacle existing on Y-axis
travel, which may cause Y-axis motor overload
and overheat. After check, reset it.
002
Z-axis servo motor driver is abnormal.
Check it.
Check the error code displayed on the Z-axis
servo motor driver. Refer to alarm code given in
the operation manual for correction. After
check, reset it.
003
Grinding wheel motor, hydraulic motor
or Y-axis elevation motor or coolant
motor is overload and skipped.
Check if grinding wheel motor, hydraulic motor,
Y-axis elevation motor or coolant motor runs
abnormally that may cause motor overload and
skip. Reset the overload protector. After check,
reset it.
004
Lubrication oil level is insufficient
Check if lubrication oil level is too low or oil
leaked or not. After check, reset it.
005
Lubrication motion fails
Check if lubrication oil hose or oil shooting is
normal or not. After check reset it.
006
Y-axis top limit switch is touched. Move
Y-axis down.
Check if Y-axis top limit switch is touched or not.
If touched, manually move Y-axis down to leave
from the limit switch. Or check if the limit switch
works normally or not. After check, reset it.
007
Z-axis forward limit switch is touched.
Move Z-axis backward.
Check if Z-axis forward limit switch is touched or
not. If touched, manually move Z-axis backward
to leave from the limit switch. Or check if the
limit switch work normally or not. After check,
reset it.
008
Z-axis backward limit switch is
touched. Move Z-axis forward.
Check if Z-axis backward limit switch is touched
or not. If touched, manually move Z-axis
forward to leave from the limit switch. Or check
if the limit switch works normally or not. After
check, reset it.
009
Z-axis forward direction change
proximity sensor is abnormal. Check it.
Check if Z-axis forward direction change
proximity sensor is damaged or not. After
check, reset it.
010
Z-axis backward direction change
proximity sensor is abnormal. Check it.
Check if Z-axis backward direction change
proximity sensor is damaged or not. After
check, reset it.
011
X-axis move leftward direction change
proximity sensor is abnormal. Check it.
Check if X-axis move leftward direction change
proximity sensor is damaged or not. After
check, reset it.
012
X-axis move rightward direction
change proximity sensor is abnormal.
Check it.
Check if X-axis move rightward direction
change proximity sensor is damaged or not.
After check, reset it.
013
Y-axis stepping motor positioning
incorrectly.
Check Y-axis motor driver.
1. To
screen
→
Set Y-axis
increasing acceleration
parameter for
/ deceleration time.
2. Turn on the Y-axis stepping motor driv
again.
er
014
Z-axis stepping motor positioning
incorrectly.
Check Z-axis motor driver
1. To
screen
→
Set Z-axis parameter for
increasing acceleration / deceleration time.
2. Turn on the Z-axis stepping motor driver
again.
015
Battery voltage for PLC control is too
low. Replace it.
When the message displays, contact the
machine manufacturer for purchasing battery
Summary of Contents for Supra 818PD
